do not press the back button…
Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
- Porsche 911 1965-1968 2.0L / 912 SWB (F)
The OE Match Front Bumper Retaining Bracket is a replacement retaining bracket used within the front bumper assembly of early Porsche 911 and 912 models from 1965–1968.
Fits:- Porsche 911/912 1965-68
Diagram Ref No 19
The bracket forms part of the bumper mounting and retention system, helping secure the front bumper components in their correct position relative to the bodywork.
What This Product Does:
The front bumper assembly relies on a number of brackets, retainers, fasteners and supports to keep it properly located on the vehicle.
The retaining bracket helps:
- Secure the front bumper assembly
- Maintain correct bumper positioning
- Support correct alignment with surrounding bodywork
- Prevent unwanted movement or vibration
- Keep associated bumper components firmly retained
- Maintain the original front-end assembly layout
- Replace a corroded, bent or missing original bracket
Although relatively small, the retaining bracket contributes to the structural stability and fit of the bumper assembly.
Symptoms Of Wear Or Failure:
Common signs of a worn or damaged bumper retaining bracket include:
Because the front bumper uses several mounting components, the complete assembly should be inspected before assuming this bracket is the only cause.
Why Replacement Matters:
A worn, damaged or missing bracket can allow the bumper assembly to move more than intended.
Continued use may cause:
- Progressive loosening of the bumper
- Damage to neighbouring mounting hardware
- Poor bumper alignment
- Rattling and vibration
- Wear to surrounding trim
- Scratching of painted bodywork
- Additional stress on other brackets or fasteners
Replacing the damaged bracket restores the correct retaining point and helps distribute loads through the original mounting arrangement.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
90150513120
The product you are viewing cross references to these numbers
- Porsche 356B 1959-63
- Porsche 356C 1963-65
This 4-piece front bumper bracket set precisely replicates the factory inner/outer mounting arms that secure the front bumper to the chassis horns on Porsche 356 B/C models. Press-formed from the correct-thickness steel with OE-style bends and slotted mounting holes for alignment, each bracket restores proper bumper position, panel gap, and contour to the front fenders. A corrosion-resistant finish helps resist rust and road grime for long service life.
Fits:
Porsche 356B 1960 - 1963
Porsche 356C 1964 - 1965
Diagram ref no 3 and 4
Includes:
2 × 64450513105 – Front bumper outer brackets (LH/RH)
2 × 64450513305 – Front bumper inner brackets (LH/RH)
Why to replace:
Front bumper brackets often suffer from rust, deformation, or impact damage over time. Corroded or bent brackets can cause misalignment, sagging corners, or uneven body gaps, affecting both appearance and structural support. Replacing them ensures the bumper sits correctly and maintains the classic Porsche contour and integrity.
When to replace:
Replacement is recommended during front-end restorations, bumper repainting, or after minor collisions. It’s also wise to install new brackets if you notice difficulty aligning the bumper or visible corrosion around the mounts.
Installation notes:
Always trial-fit the bumper loosely, align it to the body lines, and then torque fasteners securely. Use proper shims, spacers, and fresh mounting hardware or isolators to achieve perfect fit and long-term stability.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
64450513105
The product you are viewing cross references to these numbers
- Porsche 356B 1959-63
- Porsche 356C 1963-65
Fits:
Porsche 356B T5 / T6 - 1959 to 1963
Porsche 356C - 1963 to 1965
Part highlighted in green on diagram.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
64450501705
The product you are viewing cross references to these numbers
- Porsche 356B 1959-63
- Porsche 356C 1963-65
The Genuine Porsche 64450513105 Front bumper outer bracket is the factory-engineered steel mounting arm used to support and position the front bumper on Porsche 356 models. Designed for use on either the left or right side, this precision-formed bracket ensures accurate bumper alignment, correct panel gaps, and structural stability under load.
Sold each, Fits left and right side.
Fits:
Porsche 356B 1960 - 1963
Porsche 356C 1964 - 1965
Diagram ref no 3
• Position: Outer mounting bracket, fits left or right side
• Function: Connects front bumper shell to the chassis horns; supports and aligns bumper position
Over decades, the original bumper brackets may become bent, corroded, or weakened by vibration or impact, leading to poor alignment or sagging corners. Replacement is recommended when restoring the bodywork, repainting the bumper, or repairing front-end damage. Using a Genuine Porsche bracket ensures factory-correct alignment, strength, and lasting fit.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
64450513105
The product you are viewing cross references to these numbers