Brake Master Cylinder
Brake fluid DOT 4 20ltr Textar
Brake fluid is one of the most important fluids in a car as without it, stopping the vehicle safely would be impossible. The Brake fluid transmits the force exerted by the driver on the brake pedal onto the wheel brake.
To ensure perfect operation of the brakes, the brake fluid must be changed regularly during inspection or maintenance and tested with the correct brake fluid tester.
Brake fluid should be changed every two years.
The higher the DOT class, the higher the boiling temperature and wet boiling point. Higher DOT classes tend to allow longer maintenance intervals. The DOT standards are based on the American FMVSS-116 standard of the Department of Transportation (DOT).
Boiling Point and Viscosity
Dry Boiling Point - describes the property of the sealed new brake fluid. In this state, the brake fluid is almost anhydrous (substance containing no water). The dry boiling point is usually between 240 and 280°C.
Wet Boiling Point - determines the property of the brake fluid at the end of its life cycle, at a water content of 3.5% the fluid should be replaced. This defined wet boiling point must not be undercut.
Viscosity - describes the flow rate of the brake fluid. The lower the viscosity, the faster the brake fluid flows through the brake system, and the faster the brake signals are transmitted.
Important Notes
• Brake fluid is poisonous and a hazardous waste.
• Be careful when changing. The fluid weakens paints and plastics.
• It must not come into contact with eyes or skin. Always rinse spilled liquid with water.
• Do not pour the liquid into drinking water or mix with used oil.
• The colour of the brake fluid reveals nothing about its quality.
• Brake fluid should be stored in its original packaging and in a dry, cool and well-ventilated place.
Find out about Textar product verification here
Shop Securely
12 Month Warranty
Worldwide Delivery
Brake Fluid DOT 4 Brembo Premium Brake Fluid
DOT 4
Having an extremely high boiling point and lower viscosity than required, it meets and greatly exceeds regulatory standards. Also suitable for vehicles with ABS.
Vapour Lock formation
This sort of habit leaves room for the Vapour Lock, the formation of vapour bubbles due to boiling of the brake fluid that replace the normal fluid and are compressed, thereby sending the brake pedal to its fill stoke (spongy pedal). The origin is incident in the porosity of the tubes that make up the braking circuit, which in time draw moisture into the fluid, drastically reducing the boiling point. The result is a reduced braking efficiency.
Brembo Premium Brake Fluid
Brembo Premium brake fluids have a higher boiling point that exceeds the standard, thus offering superior resistance to the Vapour Lock and ensuring braking efficiency even at low temperatures. With high anti-corrosion properties and resistance to oxidation, Brembo brake fluid also allows for long-term unaltered chemical/physical characteristics of the fluid in operating circuit; therefore, preserving its integrity.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
L040
The product you are viewing cross references to these numbers
Shop Securely
12 Month Warranty
Worldwide Delivery
Brake fluid DOT 4 LV (Low Viscosity) Textar.
Brake fluid DOT 4 LV (Low Viscosity) Textar.
Textar DOT 4 LV (Low Viscosity) is especially recommended for use in hydraulic brake and clutch systems of vehicles fitted with ESP, ABS and ASR with a high boiling point and outstanding performance at very low temperatures.
DOT 4 LV (Low Viscosity)
Dry Boiling Point ≥ 260° C
Wet Boiling Point ≥ 165° C
Viscosity at -40C < 750 mm2 /s
Brake fluid is one of the most important fluids in a car as without it, stopping the vehicle safely would be impossible. The Brake fluid transmits the force exerted by the driver on the brake pedal onto the wheel brake.
To ensure perfect operation of the brakes, the brake fluid must be changed regularly during inspection or maintenance and tested with the correct brake fluid tester.
Brake fluid should be changed every two years.
The higher the DOT class, the higher the boiling temperature and wet boiling point. Higher DOT classes tend to allow longer maintenance intervals. The DOT standards are based on the American FMVSS-116 standard of the Department of Transportation (DOT).
Boiling Point and Viscosity
Dry Boiling Point - describes the property of the sealed new brake fluid. In this state, the brake fluid is almost anhydrous (substance containing no water). The dry boiling point is usually between 240 and 280°C.
Wet Boiling Point - determines the property of the brake fluid at the end of its life cycle, at a water content of 3.5% the fluid should be replaced. This defined wet boiling point must not be undercut. <
Viscosity - describes the flow rate of the brake fluid. The lower the viscosity, the faster the brake fluid flows through the brake system, and the faster the brake signals are transmitted.
Important Notes
• Brake fluid is poisonous and a hazardous waste.
• Be careful when changing. The fluid weakens paints and plastics.
• It must not come into contact with eyes or skin. Always rinse spilled liquid with water.
• Do not pour the liquid into drinking water or mix with used oil.
• The colour of the brake fluid reveals nothing about its quality.
• Brake fluid should be stored in its original packaging and in a dry, cool and well-ventilated place.
Find out about Textar product verification here
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
95006
The product you are viewing cross references to these numbers
Shop Securely
12 Month Warranty
Worldwide Delivery
Brake fluid dot 4 Textar
Brake fluid is one of the most important fluids in a car as without it, stopping the vehicle safely would be impossible. The Brake fluid transmits the force exerted by the driver on the brake pedal onto the wheel brake.
To ensure perfect operation of the brakes, the brake fluid must be changed regularly during inspection or maintenance and tested with the correct brake fluid tester.
Brake fluid should be changed every two years.
The higher the DOT class, the higher the boiling temperature and wet boiling point. Higher DOT classes tend to allow longer maintenance intervals. The DOT standards are based on the American FMVSS-116 standard of the Department of Transportation (DOT).
Boiling Point and Viscosity
Dry Boiling Point - describes the property of the sealed new brake fluid. In this state, the brake fluid is almost anhydrous (substance containing no water). The dry boiling point is usually between 240 and 280°C.
Wet Boiling Point - determines the property of the brake fluid at the end of its life cycle, at a water content of 3.5% the fluid should be replaced. This defined wet boiling point must not be undercut.
Viscosity - describes the flow rate of the brake fluid. The lower the viscosity, the faster the brake fluid flows through the brake system, and the faster the brake signals are transmitted.
Important Notes
• Brake fluid is poisonous and a hazardous waste.
• Be careful when changing. The fluid weakens paints and plastics.
• It must not come into contact with eyes or skin. Always rinse spilled liquid with water.
• Do not pour the liquid into drinking water or mix with used oil.
• The colour of the brake fluid reveals nothing about its quality.
• Brake fluid should be stored in its original packaging and in a dry, cool and well-ventilated place.
Find out about Textar product verification here
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
95002
The product you are viewing cross references to these numbers
Shop Securely
12 Month Warranty
Worldwide Delivery
Gasket between brake servo and tandem master cylinder. Porsche 95B Macan / 971 Panamera
- Porsche Panamera V6 3.0L 2WD (330 Hp)
- Porsche Panamera 4 V6 3.0L 4WD (330 Hp)
- Porsche Panamera 4 V6 3.0L 4WD Executive
- Porsche Panamera 4 3.0L Turbocharged V6 Sport Turismo
- Porsche Panamera 4S V6 3.0L 4WD (440 Hp)
- Porsche Panamera 4S V6 3.0L 4WD Executive
- Porsche Panamera 4S 2.9L Twin-Turbo V6 Sport Turismo
- Porsche Panamera 4S Diesel V8 4.0L 4WD (422 Hp)
- Porsche Panamera 4S Diesel 4.0L Twin-Turbo V8 Sport Turismo
- Porsche Panamera Turbo V8 4.0L 4WD (550 Hp)
- Porsche Panamera Turbo V8 4.0L 4WD Executive
- Porsche Panamera Turbo 4.0L Twin-Turbo V8 Sport Turismo
- Porsche Panamera 2.9L V6
- Porsche Panamera 4 2.9L V6
- Porsche Panamera 4 Sport Turismo 2.9L V6
- Porsche Panamera 4S 2.9L V6
- Porsche Panamera 4S Sport Turismo 2.9L V6
- Porsche Panamera GTS 4.0L V8
- Porsche Panamera GTS Sport Turismo 4.0L V8
- Porsche Panamera Turbo S 4.0L V8
- Porsche Panamera Turbo S Sport Turismo 4.0L V8
- Porsche Macan Petrol 2.0L 245Bhp
- Porsche Macan S Petrol 3.0L V6 354Bhp
- Porsche Macan GTS Petrol 2.9L V6 380Bhp
- Porsche Macan Turbo 2.9L V6 440Bhp
- Porsche Macan Petrol 2.0L 265Bhp
- Porsche Macan T Petrol 2.0L 265Bhp
- Porsche Macan S Petrol 2.9L V6 380Bhp
- Porsche Macan GTS Petrol 2.9L V6 440Bhp
Fits:
Porsche 95B.2 Macan 2019-21
Porsche 95B.3 Macan 2022>>
Porsche 971.1 Panamera 2017-21
Porsche 971.2 Panamera 2021>> (not Hybrid models)
Click 'Zoom in' for large parts diagram.
Diagram ref no 9
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
PAB611243
The product you are viewing cross references to these numbers
Shop Securely
12 Month Warranty
Worldwide Delivery
-
Brake Pads & Disc Package
-
Brake Disc Standard
-
Brake Pads Standard
-
SPORTS Brake Disc
-
Brembo Standard brakes
-
Brembo Racing brakes
-
TEXTAR Brakes
-
PAGID Racing Brakes
-
Zimmermann Brakes
-
SHW Performance Brakes
-
EBC Brakes
-
Brake Pad Wear Sensors
-
Brake Pad Anti-vibration shims
-
Caliper Bolts / Disc Screws
-
Pin Kit and Guide Plates
-
Performance Brake Hoses
-
Standard Brake Hoses
-
Caliper and Brake Lines
-
Brake Calipers
-
Brake Caliper Upgrades
-
HandBrake Shoes
-
Electric parking brake
-
ABS | Speed Sensors
-
Caliper Seals |Pistons
-
Brake Servo | Booster
-
Brake Fluid Reservoir
-
Brake Fluid
-
DesignTek Brake Kits
.jpg){kind=link}
.jpg){kind=link}
.jpg){kind=link}
