Price Match Guarantee
Worldwide Delivery
12 Month Warranty
Ignition Control Units
Filter by brand
Ignition kit with 6 pin basic CDI module. Porsche 911 SC and 911 turbo (USA)
Code: IGNITIONKITSCB
Vehicle Group
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1978-1989 3.3L Turbo (930)
Information
Ignition kit with basic 6 pin CDI (HKZ) module. Porsche 911SC and turbo
Fits
Porsche 911 SC 1978-1983
Porsche 911 turbo 3.3ltr 1978-1989 (US cars)
Perma-Tune Gen 6
Replace those tired and worn ignition components with this Ignition Kit
Contents of Kit
6 Pin CDI Module - Basic
Distributor with Harness
Ignition Coil
CDI Module
The Gen 6 Perma-Tune for the 911SC comes in two models: Premium ignition module and the Basic ignition module. The Basic model is just that, basic: it performs only the same functions as the analog modules did back in the day. For the average street car, this may be all that is desired and of course is more affordable than the Premium model. It is however still a high performance part and is perfect for racing venues that do not allow programmable digital ignition systems. The Basic model has a smooth, more original looking housing than the Gen 5 cast housing.
Distributor
Replacing that worn out distributor has never been easier with the Perma-Tune Bespoke distributor for the 911SC 3.0L engine and other engines like the Porsche Turbo 930 that use the six pin ignition module. There are no wires to cut and splice: the distributor has the electrical harness built in and features the original equipment compatible connectors for a plug and play installation. Simply unplug the car harness connector from the ignition module and plug it into the matching connector of the distributor harness. Then plug the distributor harness connector into the Perma-Tune module and done. There is no way to make a mistake with this installation, the connectors will only plug in the right way. The harness connector has built in diagnostics lights that tell you when the ignition system has power and when the ignition module is making sparks. The blue connector LED is a power indicator and the red connector LED is a strobe light that flashes each time the ignition system makes a spark, just like a timing light.
Ignition Coil
he Perma-Tune Black Ignition Coil is specifically designed to operate with all Perma-Tune modules to maximize the performance and service life of your Perma-Tune ignition module. It has the period correct look for the Porsche 911SC with a brown top and black body and will fit the original mounting bracket and wiring harness of the car.
The Black ignition coil is very rugged and can resist the heat and vibration that it will encounter on a classic car engine. Triple seals insure that the dielectric oil inside the coil will not leak out. The high Voltage tower is extra thick to resist arcing and will still fit the original spark plug wire boot. The internal components of the coil are designed to resist deterioration to provide a long life.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
IGNITIONKITSCB
The product you are viewing cross references to these numbers
Fits
Porsche 911 SC 1978-1983
Porsche 911 turbo 3.3ltr 1978-1989 (US cars)
Perma-Tune Gen 6
Replace those tired and worn ignition components with this Ignition Kit
Contents of Kit
6 Pin CDI Module - Basic
Distributor with Harness
Ignition Coil
CDI Module
The Gen 6 Perma-Tune for the 911SC comes in two models: Premium ignition module and the Basic ignition module. The Basic model is just that, basic: it performs only the same functions as the analog modules did back in the day. For the average street car, this may be all that is desired and of course is more affordable than the Premium model. It is however still a high performance part and is perfect for racing venues that do not allow programmable digital ignition systems. The Basic model has a smooth, more original looking housing than the Gen 5 cast housing.
Distributor
Replacing that worn out distributor has never been easier with the Perma-Tune Bespoke distributor for the 911SC 3.0L engine and other engines like the Porsche Turbo 930 that use the six pin ignition module. There are no wires to cut and splice: the distributor has the electrical harness built in and features the original equipment compatible connectors for a plug and play installation. Simply unplug the car harness connector from the ignition module and plug it into the matching connector of the distributor harness. Then plug the distributor harness connector into the Perma-Tune module and done. There is no way to make a mistake with this installation, the connectors will only plug in the right way. The harness connector has built in diagnostics lights that tell you when the ignition system has power and when the ignition module is making sparks. The blue connector LED is a power indicator and the red connector LED is a strobe light that flashes each time the ignition system makes a spark, just like a timing light.
Ignition Coil
he Perma-Tune Black Ignition Coil is specifically designed to operate with all Perma-Tune modules to maximize the performance and service life of your Perma-Tune ignition module. It has the period correct look for the Porsche 911SC with a brown top and black body and will fit the original mounting bracket and wiring harness of the car.
The Black ignition coil is very rugged and can resist the heat and vibration that it will encounter on a classic car engine. Triple seals insure that the dielectric oil inside the coil will not leak out. The high Voltage tower is extra thick to resist arcing and will still fit the original spark plug wire boot. The internal components of the coil are designed to resist deterioration to provide a long life.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
IGNITIONKITSCB
93060270200
93060270200
930602021DX
930602021DX
90160250200
90160250200
The product you are viewing cross references to these numbers
About kit
This kit is comprised of the following items:
1 x 6 Pin CDI ignition module. Porsche 911 911 turbo (USA) 1978-89 basic version (93060270200/4
1 x Distributor and harness for Porsche 911 SC and 911 turbo (USA) 1978-1989 (930602021DX/1
1 x Ignition coil Porsche 911 1969-83 & 930 1975-89 PermaTune (90160250200/3
€1,688.61
Now €1,604.18
Arriving soon
Shop Securely
12 Month Warranty
Worldwide Delivery
Ignition kit with 6 pin Gen 5 CDI module. Porsche 911 SC and 911 turbo (USA)
Code: IGNITIONKITSCG5
Vehicle Group
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1978-1989 3.3L Turbo (930)
Information
Ignition kit with 6 pin Gen 5 CDI (HKZ) module. Porsche 911SC and turbo
Fits
Porsche 911 SC 1978-1983
Porsche 911 turbo 3.3ltr 1978-1989 (US cars)
Perma-Tune Gen 5
Replace those tired and worn ignition components with this Ignition Kit
Contents of Kit
6 Pin CDI Module - Gen 5 Version
Distributor with Harness
Ignition Coil
CDI Module
The Generation 5 ignition boxes make diagnostics easier. The controller monitors and runs diagnoses programs automatically and is read by two coloured LED function lights the are viewable from underneath the unit. The diagnoses can also be done via a Bluetooth programming dongle which is available as a separate item.
Distributor
Replacing that worn out distributor has never been easier with the Perma-Tune Bespoke distributor for the 911SC 3.0L engine and other engines like the Porsche Turbo 930 that use the six pin ignition module. There are no wires to cut and splice: the distributor has the electrical harness built in and features the original equipment compatible connectors for a plug and play installation. Simply unplug the car harness connector from the ignition module and plug it into the matching connector of the distributor harness. Then plug the distributor harness connector into the Perma-Tune module and done. There is no way to make a mistake with this installation, the connectors will only plug in the right way. The harness connector has built in diagnostics lights that tell you when the ignition system has power and when the ignition module is making sparks. The blue connector LED is a power indicator and the red connector LED is a strobe light that flashes each time the ignition system makes a spark, just like a timing light.
Ignition Coil
he Perma-Tune Black Ignition Coil is specifically designed to operate with all Perma-Tune modules to maximize the performance and service life of your Perma-Tune ignition module. It has the period correct look for the Porsche 911SC with a brown top and black body and will fit the original mounting bracket and wiring harness of the car.
The Black ignition coil is very rugged and can resist the heat and vibration that it will encounter on a classic car engine. Triple seals insure that the dielectric oil inside the coil will not leak out. The high Voltage tower is extra thick to resist arcing and will still fit the original spark plug wire boot. The internal components of the coil are designed to resist deterioration to provide a long life.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
IGNITIONKITSCG5
The product you are viewing cross references to these numbers
Fits
Porsche 911 SC 1978-1983
Porsche 911 turbo 3.3ltr 1978-1989 (US cars)
Perma-Tune Gen 5
Replace those tired and worn ignition components with this Ignition Kit
Contents of Kit
6 Pin CDI Module - Gen 5 Version
Distributor with Harness
Ignition Coil
CDI Module
The Generation 5 ignition boxes make diagnostics easier. The controller monitors and runs diagnoses programs automatically and is read by two coloured LED function lights the are viewable from underneath the unit. The diagnoses can also be done via a Bluetooth programming dongle which is available as a separate item.
Distributor
Replacing that worn out distributor has never been easier with the Perma-Tune Bespoke distributor for the 911SC 3.0L engine and other engines like the Porsche Turbo 930 that use the six pin ignition module. There are no wires to cut and splice: the distributor has the electrical harness built in and features the original equipment compatible connectors for a plug and play installation. Simply unplug the car harness connector from the ignition module and plug it into the matching connector of the distributor harness. Then plug the distributor harness connector into the Perma-Tune module and done. There is no way to make a mistake with this installation, the connectors will only plug in the right way. The harness connector has built in diagnostics lights that tell you when the ignition system has power and when the ignition module is making sparks. The blue connector LED is a power indicator and the red connector LED is a strobe light that flashes each time the ignition system makes a spark, just like a timing light.
Ignition Coil
he Perma-Tune Black Ignition Coil is specifically designed to operate with all Perma-Tune modules to maximize the performance and service life of your Perma-Tune ignition module. It has the period correct look for the Porsche 911SC with a brown top and black body and will fit the original mounting bracket and wiring harness of the car.
The Black ignition coil is very rugged and can resist the heat and vibration that it will encounter on a classic car engine. Triple seals insure that the dielectric oil inside the coil will not leak out. The high Voltage tower is extra thick to resist arcing and will still fit the original spark plug wire boot. The internal components of the coil are designed to resist deterioration to provide a long life.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
IGNITIONKITSCG5
93060270200
93060270200
930602021DX
930602021DX
90160250200
90160250200
The product you are viewing cross references to these numbers
About kit
This kit is comprised of the following items:
1 x 6 Pin CDI ignition module. Porsche 911 911 turbo (USA) 1978-89 basic version (93060270200/4
1 x Distributor and harness for Porsche 911 SC and 911 turbo (USA) 1978-1989 (930602021DX/1
1 x Ignition coil Porsche 911 1969-83 & 930 1975-89 PermaTune (90160250200/3
€1,688.61
Now €1,604.18
Arriving soon
Shop Securely
12 Month Warranty
Worldwide Delivery
Ignition kit with 6 pin Premium CDI module. Porsche 911 SC and turbo (USA)
Code: IGNITIONKITSCP
Vehicle Group
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1978-1989 3.3L Turbo (930)
Information
Ignition kit with Premium 6 pin CDI (HKZ) module. Porsche 911SC and turbo
Fits
Porsche 911 SC 1978-1983
Porsche 911 turbo 3.3ltr 1978-1989 (US cars)
Perma-Tune Gen 6
Replace those tired and worn ignition components with this Ignition Kit
Contents of Kit
6 Pin CDI Module - Premium Version
Distributor with Harness
Ignition Coil
CDI Module
The Gen 6 Perma-Tune for the 911SC comes in two models:Premium ignition module and the Basic ignition module.
The Premium ignition module features a smooth, matt finish that mimics the patina of the original aluminum die cast part. It provides full control over RPM limit, mechanical advance timing, power output, multi spark function and has many other features that can be programmed using a computer, tablet or smart phone. This module comes preprogrammed for the Porsche 911SC so programming changes are optional. The Gen 6 Premium Perma-Tune makes diagnostics easier by providing onboard diagnostics that are automatically displayed by two coloured LED function lights. These LED lights assist in diagnosing both the vehicle and the ignition module. The green LED is a status indicator that can flash diagnostic fault codes. The red LED is a strobe light that flashes each time the coils fires in the same manner as a timing light. This LED is especially useful for detecting intermittent engine misfire caused by wiring or distributor problems. The LED function lights are mounted in the harness electrical connector and can only be seen when the module is powered up. There are three self-resetting overload protectors that assist in troubleshooting while protecting your Perma-Tune from damage. The overload protectors are hidden underneath the ignition module so they do not spoil the original look of the part. Refer to the Diagnostics section of this web site for more information about the diagnostics system and overload protectors.
Distributor
Replacing that worn out distributor has never been easier with the Perma-Tune Bespoke distributor for the 911SC 3.0L engine and other engines like the Porsche Turbo 930 that use the six pin ignition module. There are no wires to cut and splice: the distributor has the electrical harness built in and features the original equipment compatible connectors for a plug and play installation. Simply unplug the car harness connector from the ignition module and plug it into the matching connector of the distributor harness. Then plug the distributor harness connector into the Perma-Tune module and done. There is no way to make a mistake with this installation, the connectors will only plug in the right way. The harness connector has built in diagnostics lights that tell you when the ignition system has power and when the ignition module is making sparks. The blue connector LED is a power indicator and the red connector LED is a strobe light that flashes each time the ignition system makes a spark, just like a timing light.
Ignition Coil
he Perma-Tune Black Ignition Coil is specifically designed to operate with all Perma-Tune modules to maximize the performance and service life of your Perma-Tune ignition module. It has the period correct look for the Porsche 911SC with a brown top and black body and will fit the original mounting bracket and wiring harness of the car.
The Black ignition coil is very rugged and can resist the heat and vibration that it will encounter on a classic car engine. Triple seals insure that the dielectric oil inside the coil will not leak out. The high Voltage tower is extra thick to resist arcing and will still fit the original spark plug wire boot. The internal components of the coil are designed to resist deterioration to provide a long life.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
IGNITIONKITSCP
The product you are viewing cross references to these numbers
Fits
Porsche 911 SC 1978-1983
Porsche 911 turbo 3.3ltr 1978-1989 (US cars)
Perma-Tune Gen 6
Replace those tired and worn ignition components with this Ignition Kit
Contents of Kit
6 Pin CDI Module - Premium Version
Distributor with Harness
Ignition Coil
CDI Module
The Gen 6 Perma-Tune for the 911SC comes in two models:Premium ignition module and the Basic ignition module.
The Premium ignition module features a smooth, matt finish that mimics the patina of the original aluminum die cast part. It provides full control over RPM limit, mechanical advance timing, power output, multi spark function and has many other features that can be programmed using a computer, tablet or smart phone. This module comes preprogrammed for the Porsche 911SC so programming changes are optional. The Gen 6 Premium Perma-Tune makes diagnostics easier by providing onboard diagnostics that are automatically displayed by two coloured LED function lights. These LED lights assist in diagnosing both the vehicle and the ignition module. The green LED is a status indicator that can flash diagnostic fault codes. The red LED is a strobe light that flashes each time the coils fires in the same manner as a timing light. This LED is especially useful for detecting intermittent engine misfire caused by wiring or distributor problems. The LED function lights are mounted in the harness electrical connector and can only be seen when the module is powered up. There are three self-resetting overload protectors that assist in troubleshooting while protecting your Perma-Tune from damage. The overload protectors are hidden underneath the ignition module so they do not spoil the original look of the part. Refer to the Diagnostics section of this web site for more information about the diagnostics system and overload protectors.
Distributor
Replacing that worn out distributor has never been easier with the Perma-Tune Bespoke distributor for the 911SC 3.0L engine and other engines like the Porsche Turbo 930 that use the six pin ignition module. There are no wires to cut and splice: the distributor has the electrical harness built in and features the original equipment compatible connectors for a plug and play installation. Simply unplug the car harness connector from the ignition module and plug it into the matching connector of the distributor harness. Then plug the distributor harness connector into the Perma-Tune module and done. There is no way to make a mistake with this installation, the connectors will only plug in the right way. The harness connector has built in diagnostics lights that tell you when the ignition system has power and when the ignition module is making sparks. The blue connector LED is a power indicator and the red connector LED is a strobe light that flashes each time the ignition system makes a spark, just like a timing light.
Ignition Coil
he Perma-Tune Black Ignition Coil is specifically designed to operate with all Perma-Tune modules to maximize the performance and service life of your Perma-Tune ignition module. It has the period correct look for the Porsche 911SC with a brown top and black body and will fit the original mounting bracket and wiring harness of the car.
The Black ignition coil is very rugged and can resist the heat and vibration that it will encounter on a classic car engine. Triple seals insure that the dielectric oil inside the coil will not leak out. The high Voltage tower is extra thick to resist arcing and will still fit the original spark plug wire boot. The internal components of the coil are designed to resist deterioration to provide a long life.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
IGNITIONKITSCP
93060270200
93060270200
930602021DX
930602021DX
90160250200
90160250200
The product you are viewing cross references to these numbers
About kit
This kit is comprised of the following items:
1 x 6 Pin CDI ignition module. Porsche 911 / 911 turbo (USA) 1978-89 premium version (93060270200/3
1 x Distributor and harness for Porsche 911 SC and 911 turbo (USA) 1978-1989 (930602021DX/1
1 x Ignition coil Porsche 911 1969-83 & 930 1975-89 PermaTune (90160250200/3
€1,760.01
Now €1,672.01
In stock
Shop Securely
12 Month Warranty
Worldwide Delivery
6 pin CDI connector housing. Porsche 911
Code: 93060270200/5
Vehicle Group
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1978-1989 3.3L Turbo (930)
Information
6 pin CDI connector housing.
Fits:
Porsche 911 - 1978 to 1989
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
93060270200
The product you are viewing cross references to these numbers
Fits:
Porsche 911 - 1978 to 1989
6 pin CDI Connector Housing for Porsche 911.
This is a high quality reproduction part made from PA12 Nylon which is tough, durable, heat and chemical resistant. It is also an excellent insulator.
Please Note
Pins & wiring not included, this is only the empty housing.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
93060270200
93060270200
930602702X
930602702 X
The product you are viewing cross references to these numbers
€12.99
Now €12.34
In stock
Shop Securely
12 Month Warranty
Worldwide Delivery
6 Pin CDI ignition module. Porsche 911 / 911 turbo (USA) 1978-89 premium version
Code: 93060270200/3
Vehicle Group
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1978-1989 3.3L Turbo (930)
Information
6 Pin CDI (HKZ) ignition module.
Premium version
(Bosch Ref 0227300004)
New Perma Tune Gen 6
Disclaimer: Before fitting this CDI unit please make sure the new coil is being fitted with it. Do not try to start the car with Blue Bosch coil made in Brazil. This will damage the Perma-Tune CDI box and void the warranty.
Fits:
Porsche 911 1978-83
Porsche 930 3.3L 1978-89 (US cars only)
Take your pick: Basic or Premium
The Gen 6 Perma-Tune for the 911SC comes in two models: the Premium ignition module and the Basic ignition module.
The Premium ignition module features a smooth, matt finish that mimics the patina of the original aluminum die cast part.
It provides full control over RPM limit, mechanical advance timing, power output, multi spark function and has many other features that can be programmed using a computer, tablet or smart phone.
This comes preprogrammed for the Porsche 911SC so programming changes are optional. The programmable mechanical advance feature is very handy for restoring a distributor advance curve that has been distorted by worn mechanical parts without having to disassemble and repair the distributor.
The Gen 6 Premium Perma-Tune makes diagnostics easier by providing onboard diagnostics that are automatically displayed by two coloured LED function lights. These LED lights assist in diagnosing both the vehicle and the ignition module. The green LED is a status indicator that can flash diagnostic fault codes. The red LED is a strobe light that flashes each time the coils fires in the same manner as a timing light. This LED is especially useful for detecting intermittent engine misfire caused by wiring or distributor problems.
These LED function lights are mounted in the harness electrical connector and can only be seen when the module is powered up. There are three self-resetting overload protectors that assist in troubleshooting while protecting your Perma-Tune from damage. The overload protectors are hidden underneath the ignition module so they do not spoil the original look of the part. Refer to the Diagnostics section of this web site for more information about the diagnostics system and overload protectors.
For more information about this product Click Here
DISTRIBUTOR TRIGGER SIGNAL
The second most common cause of SC engine ignition failure is the ignition trigger circuit. Since the ignition box is controlled by the magnetic pulse generator located inside the distributor, any disruption in the triggering signal will cause the ignition box to malfunction. Be aware that the connectors can push back in the housing. Pull the rubber boot back to inspect the connection between the box and harness.
Full disassembly and inspection of the distributor is highly recommended due to the intermittent nature of triggering problems. Pay special attention to the distributor trigger shielded cable ( green wire ), magnetic pulse generator magnet and magnetic pulse generator winding connection as these parts are known to fail in combination. An especially common problem is a broken magnet pole. Evidence of arching between the magnetic pulse generator magnet points indicates a defective rotor. In this case replace the rotor, magnetic pulse winding, green wire and ignition box. The Perma-Tune high performance triggering is so accurate that worn out distributor shaft bearings can be detected by the tachometer. This is indicated by the tachometer needle slightly bouncing at idle. Trigger signal problems can cause double triggering which results in a weak ignition spark. Due to the lower triggering resolution of the stock ignition box, some symptoms of trigger signal problems can be more evident after the Perma-Tune is installed. Refer to the vehicle maintenance manual for triggering signal wave form specifications and distributor repair instructions.
To quickly test the triggering circuit without the use of an oscilloscope: Unplug the harness connector from the ignition box. Refer to the 911SC Installation Instructions diagram, connect an Ohm meter between pins 3 and 6 of the harness connector. To prevent the possibility of misdiagnosis, tug on the green triggering signal wire located at the base of the distributor while viewing the meter. The published specification for the magnetic pulse generator is 600 Ohms +- 100. Our experience has shown that a variation of +- 25 Ohm indicates a need to repair defective connections or to replace the magnetic pulse generator windings.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
93060270200
The product you are viewing cross references to these numbers
Premium version
(Bosch Ref 0227300004)
New Perma Tune Gen 6
Disclaimer: Before fitting this CDI unit please make sure the new coil is being fitted with it. Do not try to start the car with Blue Bosch coil made in Brazil. This will damage the Perma-Tune CDI box and void the warranty.
Fits:
Porsche 911 1978-83
Porsche 930 3.3L 1978-89 (US cars only)
Take your pick: Basic or Premium
The Gen 6 Perma-Tune for the 911SC comes in two models: the Premium ignition module and the Basic ignition module.
The Premium ignition module features a smooth, matt finish that mimics the patina of the original aluminum die cast part.
It provides full control over RPM limit, mechanical advance timing, power output, multi spark function and has many other features that can be programmed using a computer, tablet or smart phone.
This comes preprogrammed for the Porsche 911SC so programming changes are optional. The programmable mechanical advance feature is very handy for restoring a distributor advance curve that has been distorted by worn mechanical parts without having to disassemble and repair the distributor.
The Gen 6 Premium Perma-Tune makes diagnostics easier by providing onboard diagnostics that are automatically displayed by two coloured LED function lights. These LED lights assist in diagnosing both the vehicle and the ignition module. The green LED is a status indicator that can flash diagnostic fault codes. The red LED is a strobe light that flashes each time the coils fires in the same manner as a timing light. This LED is especially useful for detecting intermittent engine misfire caused by wiring or distributor problems.
These LED function lights are mounted in the harness electrical connector and can only be seen when the module is powered up. There are three self-resetting overload protectors that assist in troubleshooting while protecting your Perma-Tune from damage. The overload protectors are hidden underneath the ignition module so they do not spoil the original look of the part. Refer to the Diagnostics section of this web site for more information about the diagnostics system and overload protectors.
For more information about this product Click Here
DISTRIBUTOR TRIGGER SIGNAL
The second most common cause of SC engine ignition failure is the ignition trigger circuit. Since the ignition box is controlled by the magnetic pulse generator located inside the distributor, any disruption in the triggering signal will cause the ignition box to malfunction. Be aware that the connectors can push back in the housing. Pull the rubber boot back to inspect the connection between the box and harness.
Full disassembly and inspection of the distributor is highly recommended due to the intermittent nature of triggering problems. Pay special attention to the distributor trigger shielded cable ( green wire ), magnetic pulse generator magnet and magnetic pulse generator winding connection as these parts are known to fail in combination. An especially common problem is a broken magnet pole. Evidence of arching between the magnetic pulse generator magnet points indicates a defective rotor. In this case replace the rotor, magnetic pulse winding, green wire and ignition box. The Perma-Tune high performance triggering is so accurate that worn out distributor shaft bearings can be detected by the tachometer. This is indicated by the tachometer needle slightly bouncing at idle. Trigger signal problems can cause double triggering which results in a weak ignition spark. Due to the lower triggering resolution of the stock ignition box, some symptoms of trigger signal problems can be more evident after the Perma-Tune is installed. Refer to the vehicle maintenance manual for triggering signal wave form specifications and distributor repair instructions.
To quickly test the triggering circuit without the use of an oscilloscope: Unplug the harness connector from the ignition box. Refer to the 911SC Installation Instructions diagram, connect an Ohm meter between pins 3 and 6 of the harness connector. To prevent the possibility of misdiagnosis, tug on the green triggering signal wire located at the base of the distributor while viewing the meter. The published specification for the magnetic pulse generator is 600 Ohms +- 100. Our experience has shown that a variation of +- 25 Ohm indicates a need to repair defective connections or to replace the magnetic pulse generator windings.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
93060270200
93060270200
0227300004
930602702X
911SC906
The product you are viewing cross references to these numbers
€612.85
Now €582.21
In stock
Shop Securely
12 Month Warranty
Worldwide Delivery
6 Pin CDI ignition module. Porsche 911 911 turbo (USA) 1978-89 basic version
Code: 93060270200/4
Vehicle Group
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1978-1989 3.3L Turbo (930)
Information
6 Pin CDI (HKZ) ignition module.
Basic version
(Bosch Ref 0227300004)
New Perma-Tune Gen 6 Unit
Disclaimer: Before fitting this CDI unit please make sure the new coil is being fitted with it. Do not try to start the car with Blue Bosch coil made in Brazil. This will damage the Perma-Tune CDI box and void the warranty.
Fits:
Porsche 911 1978-83
Porsche 930 3.3L 1978-89 (US cars only)
Take your pick: Basic or Premium
The Gen 6 Perma-Tune for the 911SC comes in two models: the Premium ignition module and the Basic ignition module.
The Basic model is just that, basic: it performs only the same functions as the analog modules did back in the day.
For the average road car, this may be all that is desired and of course is more affordable than the Premium model.
It is however still a high performance part and is perfect for racing venues that do not allow programmable digital ignition systems. The Basic model has a smooth, more original looking housing than the Gen 5 cast housing.
For more information about this product Click Here
DISTRIBUTOR TRIGGER SIGNAL
The second most common cause of SC engine ignition failure is the ignition trigger circuit. Since the ignition box is controlled by the magnetic pulse generator located inside the distributor, any disruption in the triggering signal will cause the ignition box to malfunction. Be aware that the connectors can push back in the housing. Pull the rubber boot back to inspect the connection between the box and harness.
Full disassembly and inspection of the distributor is highly recommended due to the intermittent nature of triggering problems. Pay special attention to the distributor trigger shielded cable ( green wire ), magnetic pulse generator magnet and magnetic pulse generator winding connection as these parts are known to fail in combination. An especially common problem is a broken magnet pole. Evidence of arching between the magnetic pulse generator magnet points indicates a defective rotor. In this case replace the rotor, magnetic pulse winding, green wire and ignition box. The Perma-Tune high performance triggering is so accurate that worn out distributor shaft bearings can be detected by the tachometer. This is indicated by the tachometer needle slightly bouncing at idle. Trigger signal problems can cause double triggering which results in a weak ignition spark. Due to the lower triggering resolution of the stock ignition box, some symptoms of trigger signal problems can be more evident after the Perma-Tune is installed. Refer to the vehicle maintenance manual for triggering signal wave form specifications and distributor repair instructions.
To quickly test the triggering circuit without the use of an oscilloscope: Unplug the harness connector from the ignition box. Refer to the 911SC Installation Instructions diagram, connect an Ohm meter between pins 3 and 6 of the harness connector. To prevent the possibility of misdiagnosis, tug on the green triggering signal wire located at the base of the distributor while viewing the meter. The published specification for the magnetic pulse generator is 600 Ohms +- 100. Our experience has shown that a variation of +- 25 Ohm indicates a need to repair defective connections or to replace the magnetic pulse generator windings.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
93060270200
The product you are viewing cross references to these numbers
Basic version
(Bosch Ref 0227300004)
New Perma-Tune Gen 6 Unit
Disclaimer: Before fitting this CDI unit please make sure the new coil is being fitted with it. Do not try to start the car with Blue Bosch coil made in Brazil. This will damage the Perma-Tune CDI box and void the warranty.
Fits:
Porsche 911 1978-83
Porsche 930 3.3L 1978-89 (US cars only)
Take your pick: Basic or Premium
The Gen 6 Perma-Tune for the 911SC comes in two models: the Premium ignition module and the Basic ignition module.
The Basic model is just that, basic: it performs only the same functions as the analog modules did back in the day.
For the average road car, this may be all that is desired and of course is more affordable than the Premium model.
It is however still a high performance part and is perfect for racing venues that do not allow programmable digital ignition systems. The Basic model has a smooth, more original looking housing than the Gen 5 cast housing.
For more information about this product Click Here
DISTRIBUTOR TRIGGER SIGNAL
The second most common cause of SC engine ignition failure is the ignition trigger circuit. Since the ignition box is controlled by the magnetic pulse generator located inside the distributor, any disruption in the triggering signal will cause the ignition box to malfunction. Be aware that the connectors can push back in the housing. Pull the rubber boot back to inspect the connection between the box and harness.
Full disassembly and inspection of the distributor is highly recommended due to the intermittent nature of triggering problems. Pay special attention to the distributor trigger shielded cable ( green wire ), magnetic pulse generator magnet and magnetic pulse generator winding connection as these parts are known to fail in combination. An especially common problem is a broken magnet pole. Evidence of arching between the magnetic pulse generator magnet points indicates a defective rotor. In this case replace the rotor, magnetic pulse winding, green wire and ignition box. The Perma-Tune high performance triggering is so accurate that worn out distributor shaft bearings can be detected by the tachometer. This is indicated by the tachometer needle slightly bouncing at idle. Trigger signal problems can cause double triggering which results in a weak ignition spark. Due to the lower triggering resolution of the stock ignition box, some symptoms of trigger signal problems can be more evident after the Perma-Tune is installed. Refer to the vehicle maintenance manual for triggering signal wave form specifications and distributor repair instructions.
To quickly test the triggering circuit without the use of an oscilloscope: Unplug the harness connector from the ignition box. Refer to the 911SC Installation Instructions diagram, connect an Ohm meter between pins 3 and 6 of the harness connector. To prevent the possibility of misdiagnosis, tug on the green triggering signal wire located at the base of the distributor while viewing the meter. The published specification for the magnetic pulse generator is 600 Ohms +- 100. Our experience has shown that a variation of +- 25 Ohm indicates a need to repair defective connections or to replace the magnetic pulse generator windings.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
93060270200
93060270200
0227300004
930602702X
911SC706
The product you are viewing cross references to these numbers
€541.45
Now €514.38
Arriving soon
Shop Securely
12 Month Warranty
Worldwide Delivery
CDI ignition module Programming Cable Porsche 911 / 356 Perma Tune
Code: 90502
Vehicle Group
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1978-1989 3.3L Turbo (930)
- Porsche 356B 1959-63
- Porsche 356C 1963-65
Information
Ignition Starter box CDI (HKZ) Bluetooth Programming Cable, fits with Perma Tune 3 pin and 6 Pin Cdi boxes.
Fits:
Porsche 356 12V
Porsche 911 1974-77
Porsche 911 1978-83
Porsche 930 3.3L 1978-89
The 90502 USB Smart Wire allows you to customize your Perma-Tune Ignition module program. It plugs into the USB port of a computer and then installs itself automatically. It also powers up the module for programming with a single plug without having to connect anything else to the module. The programming software is downloaded from the internet, free, so the module settings can then be changed, saved and organized as text files.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
90502
The product you are viewing cross references to these numbers
Fits:
Porsche 356 12V
Porsche 911 1974-77
Porsche 911 1978-83
Porsche 930 3.3L 1978-89
The 90502 USB Smart Wire allows you to customize your Perma-Tune Ignition module program. It plugs into the USB port of a computer and then installs itself automatically. It also powers up the module for programming with a single plug without having to connect anything else to the module. The programming software is downloaded from the internet, free, so the module settings can then be changed, saved and organized as text files.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
90502
91160270700
90502
93060270200
93060270200
The product you are viewing cross references to these numbers
€117.81
Now €111.92
In stock
Shop Securely
12 Month Warranty
Worldwide Delivery
CDI Wiring Harness. Porsche 911 1978-83 / 930 1976-89
Code: CDI911930
Vehicle Group
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1978-1989 3.3L Turbo (930)
Information
Replaces the wiring Harness from the distributor pigtail to the CDI Box. If you need to replace from the ignition distributor to the CDI box then you will also need to add the short Green Wire part number 930.602.907.01 to complete connection.
€102.28
Now €97.17
Orderable
Shop Securely
12 Month Warranty
Worldwide Delivery
Ignition coil Porsche 911 1969-83 & 930 1975-89 PermaTune
Code: 90160250200/3
Vehicle Group
- Porsche 911 1968-1973 2.2L / 2.4L / 2.7L RS LWB (F)
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
- Porsche 356 1950-55
- Porsche 356A 1955-59
- Porsche 356B 1959-63
- Porsche 356C 1963-65
Information
Ignition Coil. Porsche 911 / 930
This coil is designed to replace the Marelli BAE202B ignition coil or Bosch 0221121001. It will work with the Porsche Perma-Tune ignition modules. It is intended to look like original equipment and is a high quality coil made in the USA.
Fits:
Porsche 911 1970-83 / 911 SC
Porsche 930 Turbo 3.0L 1975-77
Porsche 930 Turbo 3.3L 1986-89
Porsche 356 12v Only
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
90160250200
The product you are viewing cross references to these numbers
This coil is designed to replace the Marelli BAE202B ignition coil or Bosch 0221121001. It will work with the Porsche Perma-Tune ignition modules. It is intended to look like original equipment and is a high quality coil made in the USA.
Fits:
Porsche 911 1970-83 / 911 SC
Porsche 930 Turbo 3.0L 1975-77
Porsche 930 Turbo 3.3L 1986-89
Porsche 356 12v Only
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
90160250200
90160250200
108536105
The product you are viewing cross references to these numbers
€141.61
Now €134.53
In stock
Shop Securely
12 Month Warranty
Worldwide Delivery
Ignition Harness for CDI 6 PIN. Porsche 911 1978-89
Code: 93061205000
Vehicle Group
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
Information
6 Pin CDI Harness
This harness is designed to be a stand alone replacement wiring harness for the 911SC models using the 6 pin CDI system. Until now the only way to replace a damaged ignition harness on the SC models was to replace the entire engine harness. This is very expensive and time consuming to do. We have designed this harness to allow the mechanic to just replace the wiring harness that controls the ignition function of the vehicle. The harness will plug directly into the CDI Box, The Ignition distributor and coil. The only two connections that will require some plug dis-assembly are the 12V ignition connection at the rear fuse panel and the tachometer signal wire at the 14 pin plug connector. Both of these wires come with the correct connectors installed on the wires.
Fits:
Porsche 911 1978-83
Porsche 930 3.3L 1978-89
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
93061205000
The product you are viewing cross references to these numbers
This harness is designed to be a stand alone replacement wiring harness for the 911SC models using the 6 pin CDI system. Until now the only way to replace a damaged ignition harness on the SC models was to replace the entire engine harness. This is very expensive and time consuming to do. We have designed this harness to allow the mechanic to just replace the wiring harness that controls the ignition function of the vehicle. The harness will plug directly into the CDI Box, The Ignition distributor and coil. The only two connections that will require some plug dis-assembly are the 12V ignition connection at the rear fuse panel and the tachometer signal wire at the 14 pin plug connector. Both of these wires come with the correct connectors installed on the wires.
Fits:
Porsche 911 1978-83
Porsche 930 3.3L 1978-89
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
93061205000
93061205000
The product you are viewing cross references to these numbers
€368.90
Now €350.45
In stock
Shop Securely
12 Month Warranty
Worldwide Delivery
Ignition Starter Unit CDI 6 PIN. Porsche 911 1978-89 Classic Retrofit
Code: 93060270200/A
Vehicle Group
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
Information
Ignition Starter Unit CDI 6 PIN.
(Bosch Ref 0227300004)
Classic Retrofit replacement CDI+ ignition offers you bespoke modern electronics in a standard looking package. The CDI+ unit requires no modifications to the original wiring harness or vehicle metalwork and is 'plug and play'.
The CDI+ is a direct replacement for the 3 pin and 6 pin Bosch units fitted to Porsche 911's between 1969 and 1983 (and turbo models to ~1988). All CDI+ units have a 48 MHz microprocessor onboard to control ignition timing.
Advanced Unit:
The advanced unit allows the adjustment/tuning of the ignition advance curve and other features by plugging in a laptop. This can be achieved by 'overlaying' a curve on top of the distributor weights/springs curve or by locking the distributor and replacing the curve completely. Either way, you can unlock the true potential of your engine by adjusting fuelling and having the ignition curve to match.
The CDI+ has all the features of the basic unit but allow more flexibility in adjustment:
-Fully programmable ignition advance curve.
-Hard RPM limiter with adjustable ignition cut schemes
-Soft RPM limiter with adjustable ignition retard
-Launch RPM limiter
-Double spark at all RPMs
-Max RPM tell tale
-Shift Light output
-Clutch pedal input
-Tacho calibration
-Upgradeable through firmware updates
Fits:
Porsche 911 1978-83
Porsche 930 3.3L 1978-89
For 911-CDI+ Ignition Manual CLICK HERE
For 911-CDI+ Dyno Test Results CLICK HERE
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
93060270200
The product you are viewing cross references to these numbers
(Bosch Ref 0227300004)
Classic Retrofit replacement CDI+ ignition offers you bespoke modern electronics in a standard looking package. The CDI+ unit requires no modifications to the original wiring harness or vehicle metalwork and is 'plug and play'.
The CDI+ is a direct replacement for the 3 pin and 6 pin Bosch units fitted to Porsche 911's between 1969 and 1983 (and turbo models to ~1988). All CDI+ units have a 48 MHz microprocessor onboard to control ignition timing.
Advanced Unit:
The advanced unit allows the adjustment/tuning of the ignition advance curve and other features by plugging in a laptop. This can be achieved by 'overlaying' a curve on top of the distributor weights/springs curve or by locking the distributor and replacing the curve completely. Either way, you can unlock the true potential of your engine by adjusting fuelling and having the ignition curve to match.
The CDI+ has all the features of the basic unit but allow more flexibility in adjustment:
-Fully programmable ignition advance curve.
-Hard RPM limiter with adjustable ignition cut schemes
-Soft RPM limiter with adjustable ignition retard
-Launch RPM limiter
-Double spark at all RPMs
-Max RPM tell tale
-Shift Light output
-Clutch pedal input
-Tacho calibration
-Upgradeable through firmware updates
Fits:
Porsche 911 1978-83
Porsche 930 3.3L 1978-89
For 911-CDI+ Ignition Manual CLICK HERE
For 911-CDI+ Dyno Test Results CLICK HERE
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
93060270200
93060270200
930602702 X
930602702X
The product you are viewing cross references to these numbers
€1,487.50
Now €1,413.12
Orderable
Shop Securely
12 Month Warranty
Worldwide Delivery
DISPLAYING 1 to 11 (of 11 products)
Also found on these pages
You may also like
-
Air Mass/Flow Sensors
-
Alternator / Generator
-
Batteries & Chargers
-
Cold Start Valve
-
Distributor
-
Distributor Cap
-
Rotor Arms / Point Sets
-
Relays / Fuses
-
Ignition Coil
-
Ignition Lead Sets
-
Ignition Lead High Performance
-
Injectors
-
Starter Motors
-
Warm-up Regulator
-
Fuel Pump
-
Speed / Reference / Knock Sensors
-
Wiring Harness / Cables
-
Throttle Body
Popular Models
