do not press the back button…
Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
- Porsche 992.1 GT3 4.0L / 992 S/T 4.0L 2021-24
- Porsche 992.2 GT3 2025>>
The SilverRocket 4.3x3.0 CC-1 Wing Riser is a model-specific rear aero component for the Porsche 992 GT3. It repositions the original rear wing higher and further back while retaining a surface texture intended to complement the factory aluminium supports.
Fits:
Porsche 992.1 GT3 4.0L / 2021-24
Porsche 992.2 GT3 2025>>
What This Product Does
This riser raises the rear wing by 4.3 inches and extends it rearwards by 3.0 inches, creating a more prominent Cup car-inspired profile. SilverRocket states that the revised wing position can deliver equivalent downforce at a lower angle of attack, helping to manage aerodynamic drag. Raising the wing may also provide a clearer view through the rear window.
Functions
- Raises the original rear wing by 4.3 inches.
- Moves the wing rearwards by 3.0 inches.
- Provides a revised mounting position for the factory wing.
- Retains provision for setting the wing angle of attack.
- Creates a raised, motorsport-influenced rear profile.
- Uses the applicable original mounting arrangement.
Technical Details
- Product designation: SR GT3 4.3x3.0 CC-1 Wing Riser.
- Manufactured from SilverRocket proprietary CC-1 carbon composite.
- Manufacturer-reported material properties: four times stronger and 48% lighter than aluminium.
- Manufacturer-rated to withstand loads of up to 600kg of downforce.
- Processed surface designed to resemble the texture and appearance of the original aluminium wing supports.
- Designed for installation at the original mounting points without drilling additional holes.
Symptoms of Fault
- Movement or vibration from the rear wing assembly.
- Cracking around the wing supports or mounting points.
- Loose, damaged or fatigued mounting hardware.
- Uneven alignment or inconsistent spacing around the wing.
- Rattling at speed or when driving over uneven surfaces.
- Fading, peeling or deterioration of the existing support finish.
Why Replacement Matters
Loose or damaged wing supports can cause unwanted movement and make consistent rear-wing alignment difficult to maintain. This SilverRocket riser can also be used when a raised and rearward wing position is required for a particular exterior or track-focused configuration. The wing, mounting points and fasteners should be inspected before installation, followed by careful alignment and angle adjustment.
FAQs
- Does installation require drilling?
The riser is designed to use the applicable original mounting points without additional holes or complex body modifications. - Is this a universal wing riser?
No. It is a model-specific component intended for the listed Porsche 992 applications. - Should the wing angle be checked after fitting?
Yes. Confirm the angle of attack, alignment and fastener security before driving. - What should be inspected before installation?
Examine the wing, support mounting surfaces and fixings for wear, cracks or distortion. Replace any unsuitable hardware before assembly. - Will the riser change rear visibility?
Silver Rocket states that elevating the wing can improve the view through the rear window.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
SRCC1WR992GT3
The product you are viewing cross references to these numbers
- Porsche 997 MK1 Carrera 2 3.6L 2005-08
- Porsche 997 MK1 Carrera 2S 3.8L 2005-08
- Porsche 997 MK1 Carrera 4 3.6L 2005-08
- Porsche 997 MKII Carrera C2 3.6L 2009-12
- Porsche 997 MKII Carrera C4 3.6L 2009-12
- Porsche 997 MKII Carrera C2S 3.8L 2009-12
Fits:
Porsche Standard 997 Gen1
Porsche Standard 997 Gen2
Material:
Made from Fibre Glass GRP
Product Type:
Replica
Special order product that cannot be cancelled!
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
99751222592GRP
The product you are viewing cross references to these numbers
- Porsche 997 MK1 Carrera 2 3.6L 2005-08
- Porsche 997 MK1 Carrera 2S 3.8L 2005-08
- Porsche 997 MK1 Carrera 4 3.6L 2005-08
- Porsche 997 MK1 Carrera 4S 3.8L 2005-08
- Porsche 997 MK1 TURBO 2007-09
- Porsche 997 MKII Carrera C2 3.6L 2009-12
- Porsche 997 MKII Carrera C4 3.6L 2009-12
- Porsche 997 MKII Carrera C2S 3.8L 2009-12
- Porsche 997 MKII Carrera C4S 3.8L 2009-12
Fits:
Porsche Standard 997 and S models
Material:
Made from Fibre Glass GRP and Carbon
Product Type:
SpeedArt
- Porsche 997 MK1 Carrera 2 3.6L 2005-08
- Porsche 997 MK1 Carrera 2S 3.8L 2005-08
- Porsche 997 MK1 Carrera 4 3.6L 2005-08
- Porsche 997 MK1 Carrera 4S 3.8L 2005-08
- Porsche 997 MKII Carrera C2 3.6L 2009-12
- Porsche 997 MKII Carrera C4 3.6L 2009-12
- Porsche 997 MKII Carrera C2S 3.8L 2009-12
- Porsche 997 MKII Carrera C4S 3.8L 2009-12
fits:
Porsche Standard 997 and S models
Material:
Made from Fibre Glass GRP and Carbon
Product Type:
SpeedArt