do not press the back button…
Your Vehicle
Porsche // 992 (911) MK1 2019-2024 // 992.1 Carrera 2S / GTS 3.0L 2019-24
Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
- Porsche 914 (1970-1976)
Rear targa roof seal
This replacement gasket fits at the back of the removable roof where it meets the roll bar, helping maintain the seal and cushion the contact between these components.
Fits:
- Porsche 914 1970-1973 (up to VIN 47329 26221)
Diagram ref no 14
What This Product Does
The rear seal closes the joint between the targa roof panel and roll bar. It helps restrict water, draughts and exterior noise from entering the cabin while supporting a secure roof fit. A sound seal can also reduce squeaks caused by contact and movement between the roof and surrounding structure.
Functions
- Seals the rear edge of the removable targa roof
- Helps limit water and air entering through the roof joint
- Cushions contact between the roof panel and roll bar
- Helps reduce roof-related squeaks and rattles
Technical Details
- Position: rear of the targa roof
- Component description: roof-to-roll-bar gasket
- Available as self-adhering foam or high-quality rubber with a bonded fuzzy edge
- Applicable to early Porsche 914 production up to VIN 47329 26221
- Exploded diagram reference: 14
Symptoms of Fault
- Water entering around the rear corners of the roof
- Wind whistle or increased cabin noise at speed
- Squeaks or creaks from the targa panel over uneven surfaces
- Flattened, split, hardened or missing sealing material
- Visible gaps between the roof and roll bar
- Damp trim, condensation or musty odours inside the cabin
Why Replacement Matters
Age, sunlight, repeated roof removal and long-term compression can cause the original seal to shrink, harden or lose its shape. Replacing a deteriorated gasket helps restore the roof joint, reduce unwanted noise and protect the cabin and trim from moisture. Roof latches, panel alignment and adjacent seals should also be inspected, as these parts work together to provide an effective seal.
FAQs
- Does this seal fit every Porsche 914?
No. This application is specified for 1970–73 cars up to VIN 47329 26221, so the chassis number should be checked before selection. - Why might the roof still leak after fitting a new seal?
Roof-panel alignment, latch adjustment, side seals and drainage paths can also affect water sealing. Inspect these areas before making final adjustments. - What should be checked during installation?
Clean the mounting surface thoroughly and avoid stretching the seal. Confirm that the roof panel sits evenly and allow new sealing material time to settle before final latch or alignment adjustments.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
91456307711
The product you are viewing cross references to these numbers
Perfect for sealing weatherstripping to door, hood, and trunk panels.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
00004330532
The product you are viewing cross references to these numbers
- Porsche 991.1 Carrera C2 3.4L (350 Bhp) 2012-16
- Porsche 991.1 Carrera C2S / GTS 3.8L (400/430 Bhp) 2012-16
- Porsche 991.1 Carrera C4 3.4L (350 Bhp) 2012-16
- Porsche 991.1 Carrera C4S / GTS 3.8L (400/430 Bhp) 2012-16
- Porsche 991.1 Turbo 3.8L (520 Bhp) 2014-16
- Porsche 991.1 Turbo S 3.8L (560 Bhp) 2014-16
- Porsche 991.2 Carrera 2 3.0L (370 Bhp) 2016-19
- Porsche 991.2 Carrera 2S / GTS 3.0L (420/450 Bhp) 2016-19
- Porsche 991.2 Carrera 4 3.0L (370 Bhp) 2016-19
- Porsche 991.2 Carrera 4S / GTS 3.0L (420/450 Bhp) 2016-19
- Porsche 991.2 Turbo Coupe 3.8L (540 Bhp) 2016-19
- Porsche 991.2 Turbo S Coupe 3.8L (580 Bhp) 2016-19
- Porsche 992.1 Carrera 2 3.0L 2019-24
- Porsche 992.1 Carrera 4 3.0L 2019-24
- Porsche 992.1 Carrera 2S / GTS 3.0L 2019-24
- Porsche 992.1 Carrera 4S / GTS 3.0L 2019-24
- Porsche 992.1 Turbo 3.8L 2020-24
- Porsche 992.1 Turbo S 3.8L 2020-24
Fits:
Porsche 991.1 Carrera 2012-16 Coupe
Porsche 991.2 Carrera 2017-19 Coupe
Porsche 991 Turbo 2014-20 Coupe
* For vehicle with: External sliding roof (option code: 651)
* For vehicle with: External-sliding glass roof (option code: 653)
Porsche 992.1 Carrera 2019>> Coupe
Porsche 992 Turbo 2020>> Coupe
* For vehicle with: Tilting and sliding sunroof, powered (option code: 3FD)
* For vehicle with: Tilting and sliding glass sunroof with sunshade (option code: 3FE)
Click 'Zoom in' for large parts diagram.
Diagram ref no 7
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
9P1877441
The product you are viewing cross references to these numbers