do not press the back button…
Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
- Porsche 911 1965-1968 2.0L / 912 SWB (F)
- Porsche 911 1968-1973 2.2L / 2.4L / 2.7L RS LWB (F)
- Porsche 356C 1963-65
- Porsche 914 (1970-1976)
This OE Match front wheel hub end cap is a replacement protective cap for the front wheel hub assembly on classic Porsche 911, 356, and 914-6 models. This cap helps cover and protect the front wheel hub assembly, supporting wheel bearing protection and correct classic Porsche front axle detail.
Sold individually, 2 required per car, where fitted to both front hubs
Fits:
Porsche 356C (1.6) 01/1963 - 12/1965
Porsche 911 (2.0-2.7) 01/1963 - 07/1973
Porsche 914/6 (2.0) 11/1969 - 12/1973
Diagram ref no 33
The front wheel hub end cap covers the outer hub area and helps protect the wheel bearing components from dirt, moisture, and road debris. A correctly fitted cap helps keep grease contained within the hub area and supports long-term bearing reliability.
Functions
• Replaces the front wheel hub end cap
• Helps cover and protect the front hub assembly
• Helps keep dirt, water, and road debris away from the wheel bearing area
• Supports wheel bearing grease retention
• Restores correct OE-style front hub appearance
• Replaces missing, dented, corroded, loose, or damaged original caps
• OE Match replacement for classic Porsche front axle service and restoration.
Why Replace This Part?
Front wheel hub end caps can become dented, corroded, loose, damaged, or lost during wheel bearing service, brake work, hub removal, or previous repairs. A missing or damaged cap can allow contamination into the hub area, which may shorten wheel bearing life or cause premature wear. Replacing the cap helps restore correct protection and a clean original-style finish.
When to Replace This Part
• The original hub end cap is missing, loose, dented, or corroded
• Front wheel bearings have been serviced or replaced
• Grease leakage or dirt contamination is visible around the hub
• Brake disc, hub, or front suspension work is being carried out
• The front axle area is being restored
• Incorrect or non-original hub caps have been fitted
• Correct OE-style front hub detail is required
Where it fits on the car
his end cap fits on the front wheel hub assembly on Porsche 911 models up to 1973, Porsche 356, and Porsche 914-6 models. It covers the outer hub and bearing area according to the factory front axle layout.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
91434138400
The product you are viewing cross references to these numbers
for Porsche Boxster / Cayman / 911 / Panamera / Taycan
Sold each.
Fits:
Porsche 911 (993 / 996 / 997 / 991 / 992)
Porsche Boxster (986 / 987 / 981)
Porsche Cayman (987 / 981 / 718)
Porsche Panamera (970)
Porsche Taycan
Alignment eccentric washer, also referred to as a cam adjust arm or control arm adjust cam, is used in the rear suspension of certain Porsche 911, Boxster, Cayman and Panamera models.
Position on Vehicle: Rear suspension — at the rear control arm or track rod mounting point, typically used to adjust alignment of the wheel carrier, track bar or control arm.
Applications: Ideal for when original eccentric bolts or washers are worn, alignment cannot be set correctly, or when replacing control arms/track rods and correct alignment geometry is required.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
PAF007648
The product you are viewing cross references to these numbers
Cleaning kit for corroded wheel studs & adjacent hub surfaces
Removes dirt & corrosion & prepares surfaces for correct torque application
Ideal for preparing wheels, hubs and brake discs or drums for re-assembly
Suitable for use with power drill or air impact wrench
Kit contains:
- Stud cleaner body including velcro pad
- Replacement velcro pads x 2
- Fine cleaning discs x 5
- Coarse cleaning discs x 5
Find out about Textar product verification here
Aluminium bell with steel core and 12,5 mm (1/2“) seat for use on pneumatic impact screwdrivers.
Corrosion between the rim and the wheel hub is removed so torque values can no longer be distorted.
Complete with 1 cleaning disc
Find out about Textar product verification here