Please wait… 
Please wait while we process your order,
do not press the back button…
do not press the back button…
Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
Brey Krause Harness Mount Truss. Porsche 911 1974-98 COUPE - R-1025
R-1025
Vehicle Group
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
- Porsche 964 (911) C2 1989-93
- Porsche 964 (911) C4 1989-93
- Porsche 964 (911) RS 3.6L 1991-93
- Porsche 964 (911) RS 3.8L 1991-93
- Porsche 964 (911) TURBO 3.3L 1991-93
- Porsche 964 (911) TURBO 3.6L 1991-93
- Porsche 993 (911) C2 1994-97
- Porsche 993 (911) C4 1994-97
- Porsche 993 (911) RS 1994-97
- Porsche 993 (911) C2S 1994-97
- Porsche 993 (911) C4S 1994-97
- Porsche 993 (911) TURBO 1994-96
- Porsche 993 (911) GT2 1994-97
- Porsche 993 (911) TURBO S 1994-97
Information
Brey Krause Harness Mount Truss.
Fits:
Porsche 911 1974-98 COUPE
Material: 6061-T6 aluminum skeleton and reinforcing bar. Type 304 stainless steel brackets.
Finish: Anodized aluminum with satin stainless mounting brackets.
Weight: 9.44 lbs.
Models: 911 Coupes '74 - '98
Installation: Bar attaches to factory mounting points in "B" pillars.
Miscellaneous: Harness Truss is designed to allow enough seat travel for tall drivers. The stainless steel mounting brackets can be left installed in the "B" pillars to easily remove and remount the bar in minutes.
For Installation instructions please CLICK HERE
In response to the many requests from Porsche drivers looking for a harness guide bar that would not only guide their driving harnesses but also allow them to mount their harnesses directly to the bar, we developed the "Harness Truss".
The Harness Truss has been tested and certified to handle the types of forces required by the National Highway Traffic Safety Admin. DOT and SAE J385 Rev.MAR 95, Motor Vehicle Seat Belt Anchorages-Performance Requirements. It's strong, yet it weighs only a fraction of what a support of the same strength made from tubular or bar steel would weigh.
The Harness Truss is precision water-jet machined for a perfect fit into Porsche factory mounting points. This type of machining is accurate and does not create heat affected areas in the metal which can alter tensile strength. Strength requirements for harness mounts are considerably greater than those for harness guide bars since they must support the entire load applied to the belts. A mount really can't be relied upon unless it has been tested to support the loads required by the National Highway Traffic Safety Administration.
Accessories:
Seat Back Brace Adapter Bracket: R-9018
Seat Back Braces: R-9019 & R-9020 .
Fits:
Porsche 911 1974-98 COUPE
Material: 6061-T6 aluminum skeleton and reinforcing bar. Type 304 stainless steel brackets.
Finish: Anodized aluminum with satin stainless mounting brackets.
Weight: 9.44 lbs.
Models: 911 Coupes '74 - '98
Installation: Bar attaches to factory mounting points in "B" pillars.
Miscellaneous: Harness Truss is designed to allow enough seat travel for tall drivers. The stainless steel mounting brackets can be left installed in the "B" pillars to easily remove and remount the bar in minutes.
For Installation instructions please CLICK HERE
In response to the many requests from Porsche drivers looking for a harness guide bar that would not only guide their driving harnesses but also allow them to mount their harnesses directly to the bar, we developed the "Harness Truss".
The Harness Truss has been tested and certified to handle the types of forces required by the National Highway Traffic Safety Admin. DOT and SAE J385 Rev.MAR 95, Motor Vehicle Seat Belt Anchorages-Performance Requirements. It's strong, yet it weighs only a fraction of what a support of the same strength made from tubular or bar steel would weigh.
The Harness Truss is precision water-jet machined for a perfect fit into Porsche factory mounting points. This type of machining is accurate and does not create heat affected areas in the metal which can alter tensile strength. Strength requirements for harness mounts are considerably greater than those for harness guide bars since they must support the entire load applied to the belts. A mount really can't be relied upon unless it has been tested to support the loads required by the National Highway Traffic Safety Administration.
Accessories:
Seat Back Brace Adapter Bracket: R-9018
Seat Back Braces: R-9019 & R-9020 .
Price: €534.76
In stock