do not press the back button…
Your Vehicle
Porsche // 356 (1950-1965) // 356B 1959-63
Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
- Porsche 944 2.5L 8V 1982-87
- Porsche 944 2.7L 8V 1988-89
- Porsche 944S 2.5L 16V 1987-88
- Porsche 928 4.5L 1978-82
Porsche 928 1978-82 upto chassis number 92A08000749 FRONT
Porsche 924S / 924 Turbo FRONT
Porsche 944 / 944S Upto 1989 FRONT
We offer a wide selection of brake pads for fast road / trackdays and race pads.
Sold as set of 4 pads for one axle.
Please Select below
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
94435195104
The product you are viewing cross references to these numbers
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
00004330511
The product you are viewing cross references to these numbers
- Porsche 356 1950-55
- Porsche 356A 1955-59
- Porsche 356B 1959-63
- Porsche 356C 1963-65
Fits:
Porsche 356 A / 540.1, 356 B, Carrera GT and 1600 model years 1950 to 1963
Brake Shoe Set is a direct-replacement kit for use in the drum brake system of the Porsche 356 (Pre-A, A, B) models. It comprises four standard-size (40 mm) brake shoes — two for each side of one axle — manufactured with high-friction lining and correct geometry for a precise fit. According to standard listings, this set serves both front or rear drums of the Porsche 356.
It replicates the original width (40 mm) and arc length so that it fits directly into the original 356 drum hub — ideal for restoration, maintenance or performance refresh.
Brake shoes are a consumable component exposed to constant friction, heat and wear. Over time the lining material wears down, thickness reduces, and the braking arc may lose proper contact — resulting in longer stopping distances, reduced pedal feel or uneven wear.
Replace this set when:
• Shoe lining thickness falls below manufacturer spec
• Drum surface or shoe curvature shows wear/groove
• You’re restoring the braking system during a full chassis rebuild
• You observe reduced braking performance, longer stop-travel or brake fade
Installing the new Brake Shoe Set restores correct internal dimensions, ensures equal braking on both wheels and returns your Porsche 356 to safe, predictable stopping capability.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
PCG35103303
The product you are viewing cross references to these numbers
• brake, clutch and gear components
• starter motors and alternators
• carburetors, fuel pumps and engine components
• glass and metal surfaces before gluing
The advantages of Textar brake cleaner:
• does not destroy polystyrene
• does not contain any chlorinated solvents
• is listed with the German Federal Ministry for the EnvironmentHow to use:
Spray a thick coating on the parts to be cleaned. Allow the solvent to drip and/or evaporate. Repeat if necessary.
Find out about Textar product verification here
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
96000100
The product you are viewing cross references to these numbers
For brake systems and is highly temperature-resistant (up to 1,000°C).
Available in 75ml tube and 5ml sachet
The advantages of Cera Tec:
• Non-conductive and contains no solids
• Suitable for ABS
• Facilitates brake installation
• Reduces brake squealing
• Protects against scoring and corrosion
• Free of copper and acids
• Pressure-resistant / high viscosity
Cera Tec is also suitable for lubricating:• Disc- and drum-brake systems
• Compressors
• Centralised lubrication systems
• Axle bearings
• Chains
• Seat rails
• Sunroof tracks
• Battery terminals
Application:
Apply a thin layer of Cera Tec on the marked sections
Find out about Textar product verification here