do not press the back button…
Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
- Porsche 997 MK1 TURBO 2007-09
- Porsche 997 MK1 GT3 2007-09
- Porsche 997 MK1 GT2 2007-09
- Porsche 997 MKII Carrera C2 3.6L 2009-12
- Porsche 997 MKII GT3 2010-11
- Porsche 997 MKII Turbo 2010-13
- Porsche 997 MKII GT2 RS 2011-13
Rear brake pad spring clip (sometimes referred to as an anti-rattle clip or brake pad retaining clip) designed to meet original equipment standards for Porsche braking systems. This small but critical component ensures proper positioning and retention of brake pads within the rear caliper assembly, maintaining stable brake operation and minimizing noise, vibration, or pad movement during driving.
Sold each, 2 required per vehicle.
Fits:
Porsche 997.2 Carrera 2 2009 - 2012 Rear Caliper
Porsche 997.1 Turbo / GT2 2007 - 2009 Rear Caliper
Porsche 997.2 Turbo GT2 2010 - 2013 Rear Caliper
Porsche 997 GT3 2007 - 2011 Rear Caliper
Diagram ref no 11
This clip securely holds rear brake pads in their caliper bracket, keeping them aligned and preventing excessive movement. It dampens vibration, reduces brake noise, and supports consistent pad engagement with the rotor for smooth, predictable braking performance.
When installed in the brake caliper assembly, the spring clip applies controlled pressure to the brake pads, helping maintain their correct position even under rapid deceleration or repeated braking events. This function reduces hardware wear and enhances overall brake system stability.
Though small, brake pad spring clips play a vital role in brake system performance. Over time, heat cycles, corrosion, and repeated braking motions can weaken or deform the clip, leading to loose brake pads, increased noise (rattle/knock), uneven pad wear, or reduced braking feel. Replacing worn or damaged clips with new parts restores correct pad retention and contributes to smooth, quiet, and confident braking.
Replace this brake pad spring clip if:
• Rear brake pads rattle or vibrate during vehicle motion
• There is unusual noise from the brakes (especially at low speed)
• Clips appear rusted, bent, or weak upon inspection
• Brake pads are loose in the caliper bracket
• Servicing rear brake pads or calipers as part of routine maintenance
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
99735295910
The product you are viewing cross references to these numbers
For brake systems and is highly temperature-resistant (up to 1,000°C).
Available in 75ml tube and 5ml sachet
The advantages of Cera Tec:
• Non-conductive and contains no solids
• Suitable for ABS
• Facilitates brake installation
• Reduces brake squealing
• Protects against scoring and corrosion
• Free of copper and acids
• Pressure-resistant / high viscosity
Cera Tec is also suitable for lubricating:• Disc- and drum-brake systems
• Compressors
• Centralised lubrication systems
• Axle bearings
• Chains
• Seat rails
• Sunroof tracks
• Battery terminals
Application:
Apply a thin layer of Cera Tec on the marked sections
Find out about Textar product verification here