do not press the back button…
Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
- Porsche 911 1968-1973 2.2L / 2.4L / 2.7L RS LWB (F)
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
Brand New units sold without an exchange
Porsche 911 1969 - 1972 E/S
Porsche 911 1973 - 1983 2.7L / 3.0L SC
OE Match, brand-new rear “M-type” brake caliper made to match original fitment and braking performance on classic Porsche 911 models from 1969–1983. It’s sold outright (no exchange/surcharge required).
Built to OE-matching dimensions and specifications, it restores proper pad clamping and consistent braking feel when your original caliper is sticking, leaking, corroded, or worn internally. Supplied as a new unit, it avoids the downtime and core-return hassle of exchange calipers.
It converts hydraulic brake pressure into mechanical clamping force, pressing the pads onto the rotor to slow and stop the vehicle. A healthy caliper helps deliver even pad wear, stable braking response, and predictable pedal feel - especially important on older cars where original calipers may suffer from age-related corrosion and seal deterioration.
Function:
• Hydraulic-to-mechanical braking: Uses piston movement to clamp pads against the disc.
• Braking balance & stability: Supports even braking on the rear axle for controlled stops.
• Service-friendly replacement: New caliper unit simplifies restoration/maintenance without needing a core return.
A tired caliper can cause pulling under braking, uneven pad wear, overheating, leaks, or a soft/inconsistent pedal. Replacing the caliper helps restore safe, consistent braking performance and protects rotors and pads from damage caused by sticking pistons or uneven clamping.
When to replace :
• Brake fluid leak around the caliper/piston area
• Caliper sticking (wheel running hot, dragging brakes)
• Uneven pad wear side-to-side
• Pulling under braking or inconsistent pedal feel
• Corrosion damage or seized bleed screw issues during servicing
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
91135290
The product you are viewing cross references to these numbers
For brake systems and is highly temperature-resistant (up to 1,000°C).
Available in 75ml tube and 5ml sachet
The advantages of Cera Tec:
• Non-conductive and contains no solids
• Suitable for ABS
• Facilitates brake installation
• Reduces brake squealing
• Protects against scoring and corrosion
• Free of copper and acids
• Pressure-resistant / high viscosity
Cera Tec is also suitable for lubricating:• Disc- and drum-brake systems
• Compressors
• Centralised lubrication systems
• Axle bearings
• Chains
• Seat rails
• Sunroof tracks
• Battery terminals
Application:
Apply a thin layer of Cera Tec on the marked sections
Find out about Textar product verification here
Hydra tec lubricant for maintenance work and protection Textar
Available in 75ml Tube or 5ml Sachet
The Advantages of Hydra Tec:
- Facilitates the installation of hydraulic brake components
- Tested compatibility with commercially available braking fluids (DOT3, DOT4, DOT4LV, DOT5.1)
- Free of mineral oils and compatible with EPDM rubber
- In addition, running surfaces are protected against corrosion
Hydra Tec is suitable for lubricating:
- Cylinder running surfaces
- Pistons
- Sealing elements
Application:
Apply a thin layer of Hydra Tec on the marked sections.
Note:
Hydra Tec should be applied thinly and evenly.
Never use mineral oils or greases as substitutes.
Do not apply the product on friction surfaces of brake pads or brake discs.
Find out about Textar product verification here
.jpg){kind=link}
- Porsche 95B.3 Macan Petrol 2.0L (265Bhp) 2022>>
- Porsche 95B.3 Macan T Petrol 2.0L (265Bhp) 2022>>
- Porsche 95B.3 Macan S Petrol 2.9L V6 (380Bhp) 2022>>
- Porsche 95B.3 Macan GTS Petrol 2.9L V6 (440Bhp) 2022>>
Fits:
Porsche 95B.2 Macan - 2022 Onwards
For cars with Option Code - 1KW
Click 'Zoom in' for large parts diagram.
Diagram ref no 10
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
95B61542
The product you are viewing cross references to these numbers