PermaTune
About PermaTune
Advanced ignition technology with an "old school" appearance and high tech electronoics.
Perma-Tune manufactures electronic ignition systems that are period correct looking for Porsche cars while concealing the latest technology within.
Since its establishment in 1969, the Perma-Tune product line continues to be manufactured exclusively in the United States, staying true to its auto racing roots.
Vehicle Group
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
Information
Distributor and harness for 2.7ltr CIS engine with 3 PIN CDI box.
Fits:
Porsche 911 1974-77
Porsche 911 2.7S 1974-1977
New Perma Tune GEN 6 unit.
Bespoke distributor for the 911 engine with CIS injection and other engines like the Porsche Turbo 930 that use the three pin ignition module (CDI) and CIS injection
3 pin CDI with CIS injection was used from 1974 - 1978 on the 911
The Perma-Tune distributor is an exact fit, replacement part that will drop right into the engine. Setting the static timing is easy with the built in trigger point LED that lets you know when the rotor is pointing in the right direction. Idle timing is set in exactly the same way as the factory manual indicates and the factory mechanical and vacuum curves are preprogrammed into the distributor.
The mechanical vacuum can is replaced with a reliable MAP sensor that is fully programmable to perform advance, retard, vacuum and boost functions. On Turbo cars the vacuum/boost timing control can is very prone to leaks and the vacuum switches and manifold boost valves connected to the can are failure prone as well.
When these parts fail, performance deteriorates and fuel is wasted. These parts are bypassed by connecting the manifold hose directly to the MAP sensor of the distributor. It just doesn't get any easier than this.
The distributor harness is made using the same vinyl sleeve loom construction as the original wiring for that factory original look. It is very common on the Porsche 911 cars to develop engine misfire problems due to the brittle and deteriorating green shielded wire between the ignition distributor and module.
The defective wiring is replaced at the same time the new distributor is installed which cures two ills at once.
Distributors wear out and rob your engine of the horsepower it was intended to produce. Worse yet, they can leave you stranded or even damage the crankshaft ring gear.
Forget about rebuilding an outdated distributor with hard to find parts when you can replace it with modern technology that looks original. Replacing that worn out distributor has never been easier with the Perma-Tune distributor,
There are no wires to cut and splice: the distributor has the electrical harness built in and features the original equipment compatible connectors for a plug and play installation. Simply unplug the car harness connector from the ignition module and plug it into the matching connector of the distributor harness. Then plug the distributor harness connector into the Perma-Tune module and done.
There is no way to make a mistake with this installation, the connectors will only plug in the right way. The harness connector has built in diagnostics lights that tell you when the ignition system has power and when the ignition module is making sparks. The blue connector LED is a power indicator and the red connector LED is a strobe light that flashes each time the ignition system makes a spark, just like a timing light.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
911602021
The product you are viewing cross references to these numbers
Fits:
Porsche 911 1974-77
Porsche 911 2.7S 1974-1977
New Perma Tune GEN 6 unit.
Bespoke distributor for the 911 engine with CIS injection and other engines like the Porsche Turbo 930 that use the three pin ignition module (CDI) and CIS injection
3 pin CDI with CIS injection was used from 1974 - 1978 on the 911
The Perma-Tune distributor is an exact fit, replacement part that will drop right into the engine. Setting the static timing is easy with the built in trigger point LED that lets you know when the rotor is pointing in the right direction. Idle timing is set in exactly the same way as the factory manual indicates and the factory mechanical and vacuum curves are preprogrammed into the distributor.
The mechanical vacuum can is replaced with a reliable MAP sensor that is fully programmable to perform advance, retard, vacuum and boost functions. On Turbo cars the vacuum/boost timing control can is very prone to leaks and the vacuum switches and manifold boost valves connected to the can are failure prone as well.
When these parts fail, performance deteriorates and fuel is wasted. These parts are bypassed by connecting the manifold hose directly to the MAP sensor of the distributor. It just doesn't get any easier than this.
The distributor harness is made using the same vinyl sleeve loom construction as the original wiring for that factory original look. It is very common on the Porsche 911 cars to develop engine misfire problems due to the brittle and deteriorating green shielded wire between the ignition distributor and module.
The defective wiring is replaced at the same time the new distributor is installed which cures two ills at once.
Distributors wear out and rob your engine of the horsepower it was intended to produce. Worse yet, they can leave you stranded or even damage the crankshaft ring gear.
Forget about rebuilding an outdated distributor with hard to find parts when you can replace it with modern technology that looks original. Replacing that worn out distributor has never been easier with the Perma-Tune distributor,
There are no wires to cut and splice: the distributor has the electrical harness built in and features the original equipment compatible connectors for a plug and play installation. Simply unplug the car harness connector from the ignition module and plug it into the matching connector of the distributor harness. Then plug the distributor harness connector into the Perma-Tune module and done.
There is no way to make a mistake with this installation, the connectors will only plug in the right way. The harness connector has built in diagnostics lights that tell you when the ignition system has power and when the ignition module is making sparks. The blue connector LED is a power indicator and the red connector LED is a strobe light that flashes each time the ignition system makes a spark, just like a timing light.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
911602021
911CF126
0231169011
0231184001
0231184002
0231184003
0231184004
0231184007
901602021EX
91160202103
91160202107
91160202703
911602027CX
91160203103
91160203105
91160203106
911602031CX
93060210100
930602101X
930602101 X
The product you are viewing cross references to these numbers
Price: £785.00
In stock
Shop Securely
12 Month Warranty
Worldwide Delivery
Vehicle Group
- Porsche 911 1968-1973 2.2L / 2.4L / 2.7L RS LWB (F)
Information
Distributor and harness for 911 MFI Engines with 3 Pin CDI box
For MFI engines with 3 Pin CDI Box (Mechanical Fuel Injection)
Fits:
Porsche 911 2.4 ltr - T, E and S 1972-1973
Porsche 911 2.7RS 1973
New Perma Tune GEN 6 unit.
The bespoke Porsche distributor for mechanically injected engines is an exact fit replacement part that will drop right into the engine.
Setting the static timing is easy with the built in trigger point LED that lets you know when the rotor is pointing in the right direction.
Idle timing is set in exactly the same way as the factory manual indicates and the factory mechanical and vacuum curves are preprogrammed into the distributor.
The mechanical vacuum can is replaced with a reliable MAP sensor that is fully programmable for both vacuum/pressure and retard/advance settings. It just doesn't get any easier than this.
3 pin CDI was used from 1969 - 1978
The distributor harness is made using the same vinyl sleeve loom construction as the original wiring for that factory original look. It is very common on the Porsche 911 cars to develop engine misfire problems due to the brittle and deteriorating green shielded wire between the ignition distributor and module.
The defective wiring is replaced at the same time the new distributor is installed which cures two ills at once.
Distributors wear out and rob your engine of the horsepower it was intended to produce. Worse yet, they can leave you stranded or even damage the crankshaft ring gear.
Forget about rebuilding an outdated distributor with hard to find parts when you can replace it with modern technology that looks original. Replacing that worn out distributor has never been easier with the Perma-Tune distributor.
There are no wires to cut and splice: the distributor has the electrical harness built in and features the original equipment compatible connectors for a plug and play installation. Simply unplug the car harness connector from the ignition module and plug it into the matching connector of the distributor harness. Then plug the distributor harness connector into the Perma-Tune module and done There is no way to make a mistake with this installation, the connectors will only plug in the right way. The harness connector has built in diagnostics lights that tell you when the ignition system has power and when the ignition module is making sparks. The blue connector LED is a power indicator and the red connector LED is a strobe light that flashes each time the ignition system makes a spark, just like a timing light.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
911602021
The product you are viewing cross references to these numbers
For MFI engines with 3 Pin CDI Box (Mechanical Fuel Injection)
Fits:
Porsche 911 2.4 ltr - T, E and S 1972-1973
Porsche 911 2.7RS 1973
New Perma Tune GEN 6 unit.
The bespoke Porsche distributor for mechanically injected engines is an exact fit replacement part that will drop right into the engine.
Setting the static timing is easy with the built in trigger point LED that lets you know when the rotor is pointing in the right direction.
Idle timing is set in exactly the same way as the factory manual indicates and the factory mechanical and vacuum curves are preprogrammed into the distributor.
The mechanical vacuum can is replaced with a reliable MAP sensor that is fully programmable for both vacuum/pressure and retard/advance settings. It just doesn't get any easier than this.
3 pin CDI was used from 1969 - 1978
The distributor harness is made using the same vinyl sleeve loom construction as the original wiring for that factory original look. It is very common on the Porsche 911 cars to develop engine misfire problems due to the brittle and deteriorating green shielded wire between the ignition distributor and module.
The defective wiring is replaced at the same time the new distributor is installed which cures two ills at once.
Distributors wear out and rob your engine of the horsepower it was intended to produce. Worse yet, they can leave you stranded or even damage the crankshaft ring gear.
Forget about rebuilding an outdated distributor with hard to find parts when you can replace it with modern technology that looks original. Replacing that worn out distributor has never been easier with the Perma-Tune distributor.
There are no wires to cut and splice: the distributor has the electrical harness built in and features the original equipment compatible connectors for a plug and play installation. Simply unplug the car harness connector from the ignition module and plug it into the matching connector of the distributor harness. Then plug the distributor harness connector into the Perma-Tune module and done There is no way to make a mistake with this installation, the connectors will only plug in the right way. The harness connector has built in diagnostics lights that tell you when the ignition system has power and when the ignition module is making sparks. The blue connector LED is a power indicator and the red connector LED is a strobe light that flashes each time the ignition system makes a spark, just like a timing light.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
911602021
911MF126
0231159001
0231159006
0231169001
0231169003
0231169004
0231169005
0231169008
0231169009
0231169010
90160202101
90160202102
90160202104
901602021CX
90160202700
901603021BX
91160202101
91160202102
91160202103
91160202701
91160202702
91160202703
91160203101
91160203104
The product you are viewing cross references to these numbers
Price: £755.00
In stock
Shop Securely
12 Month Warranty
Worldwide Delivery
Vehicle Group
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
Information
Distributor and harness for 911 SC and turbo with 6 PIN CDI box.
Porsche 911 1978-89.
Fits:
Porsche 911 SC 1978-83
Porsche 930 3.0ltr 1975-77 (US cars only)
Porsche 930 3.3ltr 1978-89 (US cars only)
New Perma Tune GEN 6 unit.
Bespoke distributor for the 911SC 3.0ltr engine and other engines like the Porsche Turbo 930 that use the six pin ignition module (CDI) and CIS injection
6 pin CDI was used from 1978 - 1983 on 911 and 1978 - 1989 on the turbo
The Perma-Tune distributor is an exact fit, replacement part that will drop right into the engine. Setting the static timing is easy with the built in trigger point LED that lets you know when the rotor is pointing in the right direction.
Idle timing is set in exactly the same way as the factory manual indicates and the factory mechanical and vacuum curves are preprogrammed into the distributor.
The mechanical vacuum can is replaced with a reliable MAP sensor that is fully programmable to perform advance, retard, vacuum and boost functions.
On Turbo cars the vacuum/boost timing control can is very prone to leaks and the vacuum switches and manifold boost valves connected to the can are failure prone as well.
When these parts fail, performance deteriorates and fuel is wasted. These parts are bypassed by connecting the manifold hose directly to the MAP sensor of the distributor.
It just doesn't get any easier than this.
The distributor harness is made using the same vinyl sleeve loom construction as the original wiring for that factory original look. It is very common on the Porsche 911 cars to develop engine misfire problems due to the brittle and deteriorating green shielded wire between the ignition distributor and module.
The defective wiring is replaced at the same time the new distributor is installed which cures two ills at once.
Distributors wear out and rob your engine of the horsepower it was intended to produce. Worse yet, they can leave you stranded or even damage the crankshaft ring gear.
Forget about rebuilding an outdated distributor with hard to find parts when you can replace it with modern technology that looks original. Replacing that worn out distributor has never been easier with the Perma-Tune distributor.
There are no wires to cut and splice: the distributor has the electrical harness built in and features the original equipment compatible connectors for a plug and play installation. Simply unplug the car harness connector from the ignition module and plug it into the matching connector of the distributor harness. Then plug the distributor harness connector into the Perma-Tune module and done There is no way to make a mistake with this installation, the connectors will only plug in the right way.
The harness connector has built in diagnostics lights that tell you when the ignition system has power and when the ignition module is making sparks. The blue connector LED is a power indicator and the red connector LED is a strobe light that flashes each time the ignition system makes a spark, just like a timing light.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
930602021DX
The product you are viewing cross references to these numbers
Porsche 911 1978-89.
Fits:
Porsche 911 SC 1978-83
Porsche 930 3.0ltr 1975-77 (US cars only)
Porsche 930 3.3ltr 1978-89 (US cars only)
New Perma Tune GEN 6 unit.
Bespoke distributor for the 911SC 3.0ltr engine and other engines like the Porsche Turbo 930 that use the six pin ignition module (CDI) and CIS injection
6 pin CDI was used from 1978 - 1983 on 911 and 1978 - 1989 on the turbo
The Perma-Tune distributor is an exact fit, replacement part that will drop right into the engine. Setting the static timing is easy with the built in trigger point LED that lets you know when the rotor is pointing in the right direction.
Idle timing is set in exactly the same way as the factory manual indicates and the factory mechanical and vacuum curves are preprogrammed into the distributor.
The mechanical vacuum can is replaced with a reliable MAP sensor that is fully programmable to perform advance, retard, vacuum and boost functions.
On Turbo cars the vacuum/boost timing control can is very prone to leaks and the vacuum switches and manifold boost valves connected to the can are failure prone as well.
When these parts fail, performance deteriorates and fuel is wasted. These parts are bypassed by connecting the manifold hose directly to the MAP sensor of the distributor.
It just doesn't get any easier than this.
The distributor harness is made using the same vinyl sleeve loom construction as the original wiring for that factory original look. It is very common on the Porsche 911 cars to develop engine misfire problems due to the brittle and deteriorating green shielded wire between the ignition distributor and module.
The defective wiring is replaced at the same time the new distributor is installed which cures two ills at once.
Distributors wear out and rob your engine of the horsepower it was intended to produce. Worse yet, they can leave you stranded or even damage the crankshaft ring gear.
Forget about rebuilding an outdated distributor with hard to find parts when you can replace it with modern technology that looks original. Replacing that worn out distributor has never been easier with the Perma-Tune distributor.
There are no wires to cut and splice: the distributor has the electrical harness built in and features the original equipment compatible connectors for a plug and play installation. Simply unplug the car harness connector from the ignition module and plug it into the matching connector of the distributor harness. Then plug the distributor harness connector into the Perma-Tune module and done There is no way to make a mistake with this installation, the connectors will only plug in the right way.
The harness connector has built in diagnostics lights that tell you when the ignition system has power and when the ignition module is making sparks. The blue connector LED is a power indicator and the red connector LED is a strobe light that flashes each time the ignition system makes a spark, just like a timing light.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
930602021DX
0237301001
0237301002
0237301007
0237301009
0237302034
0237302045
0237303003
0237304016
0237306001
0237505001
91160202109
93060201002
93060202100
93060202102
93060202104
93060202106
93060202300
93060210400
93060292300
The product you are viewing cross references to these numbers
Price: £845.00
In stock
Shop Securely
12 Month Warranty
Worldwide Delivery
Vehicle Group
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1978-1989 3.3L Turbo (930)
- Porsche 356B 1959-63
- Porsche 356C 1963-65
Information
Ignition Starter box CDI (HKZ) Bluetooth Programming Cable, fits with Perma Tune 3 pin and 6 Pin Cdi boxes.
Fits:
Porsche 356 12V
Porsche 911 1974-77
Porsche 911 1978-83
Porsche 930 3.3L 1978-89
The 90502 USB Smart Wire allows you to customize your Perma-Tune Ignition module program. It plugs into the USB port of a computer and then installs itself automatically. It also powers up the module for programming with a single plug without having to connect anything else to the module. The programming software is downloaded from the internet, free, so the module settings can then be changed, saved and organized as text files.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
90502
The product you are viewing cross references to these numbers
Fits:
Porsche 356 12V
Porsche 911 1974-77
Porsche 911 1978-83
Porsche 930 3.3L 1978-89
The 90502 USB Smart Wire allows you to customize your Perma-Tune Ignition module program. It plugs into the USB port of a computer and then installs itself automatically. It also powers up the module for programming with a single plug without having to connect anything else to the module. The programming software is downloaded from the internet, free, so the module settings can then be changed, saved and organized as text files.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
90502
91160270700
90502
93060270200
93060270200
The product you are viewing cross references to these numbers
Price: £99.00
In stock
Shop Securely
12 Month Warranty
Worldwide Delivery
Vehicle Group
- Porsche 911 1965-1968 2.0L / 912 SWB (F)
- Porsche 356 1950-55
- Porsche 356A 1955-59
- Porsche 356B 1959-63
- Porsche 356C 1963-65
Information
Ignition module. Porsche 356 or early 911 12 Volt or 8 Volt ignition cars.
Disclaimer: Before fitting this CDI unit please make sure the new PERMA-TUNE coil is being fitted with it. Do not try to start the car with Blue Bosch coil made in Brazil. This will damage the Perma-Tune CDI box and void the warranty. If CDI unit was not purchased with the PERMA-TUNE coil the warranty will not be respected. Fitting with other brand coils at your own risk.
Bluetooth programmable (Bluetooth Smart Wire required part no 90506)
Brand: Perma Tune
This is an upgrade for the ignition system. Basically it puts the load of the ignition system through the box rather than the distributor. You take the existing wiring and run it through this box and the points then become an earth trigger switch for the box rather than switching the coil.
This Model is the first of a brand new product line for Perma-Tune. We have combined our accumulated knowledge of Porsche ignition over the last 48 years and applied it to the very latest electronics technology to produce a state of the art electronic ignition module that is period correct looking. Made to look like an old school electrical relay, it blends right into the engine bay of a 356 or an early 911.
NO CRIMPS, NO MESS, NO HEADACHES
Plug and play features eliminate the need for wire crimps and complicated wiring diagrams. Wires are cut and stripped, then inserted into the wire bus for a secure, plug in connection without the need for special tools or wire crimps.
Simple, four wire installation. There is no need to interpret complicated wiring diagrams, the terminals are clearly marked so you know exactly where each wire goes.
NO DIALS, NO SWITCHES, NO PROBLEMS
Installation is easy. There are no dials to turn, no switches to set and no chips to plug in. The 356906 Perma-Tune comes to you pre-programmed and ready to be installed on a 356. You can always customise the module later using your wireless device to make secure, reliable configuration changes through the built in Bluetooth connection.
STRONG, YET FORGIVING
The Perma-Tune ignition module features on board diagnostics to help you install the module. The built in strobe light can help you check your ignition timing. It also has self resetting overload protection so there are no fuses to replace.
SMART CONNECTIONS
Use any kind of distributor you have. The Points distributor connection will work with breaker points or any aftermarket distributor.
The tachometer output connection is universal and will work with the stock tachometer or aftermarket electronic tachometer, shift light and RPM switch.
Power connects to 12 Volt or 8 Volt systems. Six Volt converters are not available at this time.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
356906
The product you are viewing cross references to these numbers
Disclaimer: Before fitting this CDI unit please make sure the new PERMA-TUNE coil is being fitted with it. Do not try to start the car with Blue Bosch coil made in Brazil. This will damage the Perma-Tune CDI box and void the warranty. If CDI unit was not purchased with the PERMA-TUNE coil the warranty will not be respected. Fitting with other brand coils at your own risk.
Bluetooth programmable (Bluetooth Smart Wire required part no 90506)
Brand: Perma Tune
This is an upgrade for the ignition system. Basically it puts the load of the ignition system through the box rather than the distributor. You take the existing wiring and run it through this box and the points then become an earth trigger switch for the box rather than switching the coil.
This Model is the first of a brand new product line for Perma-Tune. We have combined our accumulated knowledge of Porsche ignition over the last 48 years and applied it to the very latest electronics technology to produce a state of the art electronic ignition module that is period correct looking. Made to look like an old school electrical relay, it blends right into the engine bay of a 356 or an early 911.
NO CRIMPS, NO MESS, NO HEADACHES
Plug and play features eliminate the need for wire crimps and complicated wiring diagrams. Wires are cut and stripped, then inserted into the wire bus for a secure, plug in connection without the need for special tools or wire crimps.
Simple, four wire installation. There is no need to interpret complicated wiring diagrams, the terminals are clearly marked so you know exactly where each wire goes.
NO DIALS, NO SWITCHES, NO PROBLEMS
Installation is easy. There are no dials to turn, no switches to set and no chips to plug in. The 356906 Perma-Tune comes to you pre-programmed and ready to be installed on a 356. You can always customise the module later using your wireless device to make secure, reliable configuration changes through the built in Bluetooth connection.
STRONG, YET FORGIVING
The Perma-Tune ignition module features on board diagnostics to help you install the module. The built in strobe light can help you check your ignition timing. It also has self resetting overload protection so there are no fuses to replace.
SMART CONNECTIONS
Use any kind of distributor you have. The Points distributor connection will work with breaker points or any aftermarket distributor.
The tachometer output connection is universal and will work with the stock tachometer or aftermarket electronic tachometer, shift light and RPM switch.
Power connects to 12 Volt or 8 Volt systems. Six Volt converters are not available at this time.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
356906
356906
910905
The product you are viewing cross references to these numbers
Price: £475.00
In stock
Shop Securely
12 Month Warranty
Worldwide Delivery
Vehicle Group
- Porsche 911 1968-1973 2.2L / 2.4L / 2.7L RS LWB (F)
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
- Porsche 356 1950-55
- Porsche 356A 1955-59
- Porsche 356B 1959-63
- Porsche 356C 1963-65
Information
Ignition Coil. Porsche 911 / 930
This coil is designed to replace the Marelli BAE202B ignition coil or Bosch 0221121001. It will work with the Porsche Perma-Tune ignition modules. It is intended to look like original equipment and is a high quality coil made in the USA.
Fits:
Porsche 911 1970-83 / 911 SC
Porsche 930 Turbo 3.0L 1975-77
Porsche 930 Turbo 3.3L 1986-89
Porsche 356 12v Only
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
PCG602502A
The product you are viewing cross references to these numbers
This coil is designed to replace the Marelli BAE202B ignition coil or Bosch 0221121001. It will work with the Porsche Perma-Tune ignition modules. It is intended to look like original equipment and is a high quality coil made in the USA.
Fits:
Porsche 911 1970-83 / 911 SC
Porsche 930 Turbo 3.0L 1975-77
Porsche 930 Turbo 3.3L 1986-89
Porsche 356 12v Only
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
PCG602502A
90160250200
108536105
PCG602502A
The product you are viewing cross references to these numbers
Price: £119.00
In stock
Shop Securely
12 Month Warranty
Worldwide Delivery